参数资料
| 型号： | ADT7462ZEVB |
| 厂商： | ON Semiconductor |
| 文件页数： | 50/82页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADT7462 |
| 产品变化通告： | MFG CHG Notification ADI to ON Semi |
| 标准包装： | 1 |
| 类型： | 温度传感器 |
| 适用于相关产品： | ADT7462 |
| 所含物品： | 评估板 |
| 其它名称： | EVAL-ADT7462EBZ EVAL-ADT7462EBZ-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
ADT7462
The freewheeling test procedure is as follows:
1. PWM1 and PWM2 go to full speed, and PWM3
and PWM4 are switched off.
2. After the spin-up time of PWM1 and PWM2 has
elapsed, the speed of Fan 1, Fan 2, Fan 3, and
Fan 4 is measured.
3. After the speed of Fan 1 and Fan 2 is measured,
PWM1 is switched off and PWM3 is spun up.
After the spin-up time for PWM3 has elapsed, the
speed of Fan 5 and Fan 6 is measured.
4. After the speed of Fan 3 and Fan 4 is measured,
PWM2 is switched off and PWM4 is switched on.
After the spin-up time of PWM4 has elapsed, the
speed of Fan 7 and Fan 8 is measured.
5. After the speed of all eight fans has been
measured, the TACH and PWM configurations
return to their previous values.
register (0xBD) should be read directly after completion of
the test.
THERM I/O Operation
This section describes the operation of THERM1 and
THERM2. Pin 28 and Pin 29 can both be configured as
THERM inputs or outputs.
THERM Output
THERM is not enabled as an output by default on powerup,
but it can be enabled by setting the appropriate bits in
Register 0x0E (THERM1 configuration register) and
Register 0x0F (THERM2 configuration register). THERM1
and THERM2 can be configured to assert whenever a
specific channel exceeds the specified THERM limit (see
Table 30).
Table 30. THERM OUTPUT CHANNEL SELECT AND
? Fans must be in continuous mode for the
freewheeling test; that is, the dc bits must be set
(Register 0x08).
? To enable the freewheeling test, set the
freewheeling test enable register (0x1E) to a
LIMITS
Channel
Enable
Configuration
THERM1, THERM2,
Register Register
0x0E 0x0F
Limit Registers
THERM1 THERM2
nonzero value. Set Bit 0 = 1 to enable the
freewheeling test for Fan 1, and set Bit 1 for Fan 2,
all the way to Bit 7 for Fan 8. The freewheeling
test enable register should be programmed after the
fans present register is programmed. If the fans
Local
Remote 1
Remote 2
Remote 3
Bit 1 = 1
Bit 2 = 1
Bit 3 = 1
Bit 4 = 1
Bit 1 = 1
Bit 2 = 1
Bit 3 = 1
Bit 4 = 1
0x4C
0x4D
0x4E
0x4F
0x50
0x51
0x52
0x53
present register is not programmed first, then the
values in the two registers do not match, and the
ADT7462 assumes that a fan is missing.
The following registers must be programmed for the fan
freewheeling test:
Fans Present Register (0x1D)
Set Bit 0 to 1 when a fan is connected to TACH1.
Set Bit 1 to 1 when a fan is connected to TACH2.
Set Bit 2 to 1 when a fan is connected to TACH3.
Set Bit 3 to 1 when a fan is connected to TACH4.
Set Bit 4 to 1 when a fan is connected to TACH5.
Set Bit 5 to 1 when a fan is connected to TACH6.
As an output, THERM is asserted low to signal that the
measured THERM temperature has exceeded pre-
programmed THERM temperature limits. The output is
automatically pulled high again when the temperature falls
below the (THERM ? Hysteresis) limit. The value of
hysteresis for each channel is programmable in Register
0x54 and Register 0x55, where 1 LSB = 1 ? C, and the
maximum hysteresis for each channel is 15 ? C.
Setting the THERM boost bits, Bit 0 and Bit 1, to Logic 0
(default setting) in the THERM configuration register
(0x0D), sets the fans to full speed on an internal THERM
event.
Set Bit 6 to 1 when a fan is connected to TACH7.
Set Bit 7 to 1 when a fan is connected to TACH8.
THERM Input
To configure THERM
as an input, the
Fan Freewheeling Test Enable Register (0x1E)
Set Bit 0 to 1 to enable the freewheeling test for Fan 1.
Set Bit 1 to 1 to enable the freewheeling test for Fan 2.
Set Bit 2 to 1 to enable the freewheeling test for Fan 3.
Set Bit 3 to 1 to enable the freewheeling test for Fan 4.
Set Bit 4 to 1 to enable the freewheeling test for Fan 5.
Set Bit 5 to 1 to enable the freewheeling test for Fan 6.
Set Bit 6 to 1 to enable the freewheeling test for Fan 7.
Set Bit 7 to 1 to enable the freewheeling test for Fan 8.
Fan Freewheeling Test Register (0x1C)
Both the Fans Present register (0x1D) and the
freewheeling test enable register (0x1E) should be
programmed before setting the relevant bits in the fan
freewheeling test register (0x1C). The host fan status
THERM1_Timer_Enable (T1TE) bit (Bit 0) in the
THERM1 configuration register (0x0E) and the
THERM2_Timer_Enable (T2TE) bit (Bit 0) in the
THERM2 configuration register (0x0F) must be set to
Logic 1. The ADT7462 can then be used to detect when the
THERM pins are asserted low. The THERM pins can be
connected to a trip point temperature sensor or to the
PROCHOT output of a CPU.
With processor core voltages reducing all the time, the
threshold for the AGTL + PROCHOT output is also reduced
as new processors become available.
Because the THERM input is typically an AGTL + input,
the thresholds can be referenced to V CCP . By setting Bit 4 of
Configuration Register 3 (0x03) to 1, the THERM threshold
http://onsemi.com
50
相关PDF资料 |
PDF描述 |
|---|---|
| ADT7467BBZEVB | BOARD EVALUATION FOR ADT7467 |
| ADT7468ZEVB | BOARD EVAL FOR ADT7468 |
| ADT7473ZEVB | BOARD EVALUATION FOR ADT7473 |
| ADT7475EBZEVB | BOARD EVALUATION FOR ADT7475 |
| ADT7476EBZEVB | BOARD EVALUATION FOR ADT7476 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADT7463 | 制造商:AD 制造商全称:Analog Devices 功能描述:dB COOL Remote Thermal Controller and Voltage Monitor |
| ADT7463ARQ | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7463ARQ-REEL | 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7463ARQ-REEL7 | 功能描述:IC SENSOR TEMP FAN-CTRL 24QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热管理 系列:dBCool® 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| ADT7463ARQZ | 功能描述:马达/运动/点火控制器和驱动器 SYS MGMT CNTRLR IC RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。