- 您现在的位置：买卖IC网 > PDF目录11203 > ADUC7032BSTZ-88-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LQFP PDF资料下载
参数资料
| 型号： | ADUC7032BSTZ-88-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 11/120页 |
| 文件大小： | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LQFP |
| 标准包装： | 2,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI，UART/USART |
| 外围设备： | POR，PSM，温度传感器，WDT |
| 输入/输出数： | 9 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页
ADuC7032-8L
Rev. A | Page 108 of 120
LIN HARDWARE INTERFACE
LIN Frame Protocol
The LIN frame protocol is divided into four main categories:
break symbol, sync byte, protected identifier, and data bytes.
The format of the frame header, break, synchronization byte,
and protected identifier is shown in Figure 41. Essentially, the
embedded UART, LIN hardware synchronization logic, and the
high voltage transceiver interface all combine on-chip to support
and manage LIN-based transmissions and receptions.
LIN Frame Break Symbol
As shown in Figure 42, the LIN break symbol is used to signal
the start of a new frame. It lasts at least 13 bit-periods, and
a slave must be able to detect a break symbol, even if it expects
data or is in the process of receiving data. The ADuC7032-8L
accomplishes this by using the LHSVAL1 break condition and
break error-detect functionality. The break period does not
need to be accurately measured, but if a bus fault condition
(bus held low) occurs, it must be flagged.
LIN Frame Synchronization Byte
The baud rate of the communication via LIN is calculated from
the sync byte, as shown in Figure 43. The time between the first
falling edge of the sync field and the fifth falling edge of the sync
field is measured. The result is divided by 8 to give the baud
rate of the data that is to be transmitted. The ADuC7032-8L
implements the timing of this sync byte in hardware.
LIN Frame Protected Identifier
After receiving the LIN sync field, the required baud rate for
the UART is calculated. The UART is then configured, allowing
the ADuC7032-8L to receive the protected identifier, as shown
in Figure 44. The protected identifier consists of two sub-fields:
the identifier and the identifier parity. The 6-bit identifier
contains the identifier of the target for the frame. The identifier
signifies the number of data bytes to be either received or
transmitted.
The number of bytes is user-configurable at system level design.
The parity is calculated on the identifier and is dependent on
the revision of LIN for which the system is designed.
LIN Frame Data Byte
The data byte frame carries between one byte and eight bytes of
data. The number of bytes contained in the frame is dependent
on the LIN master. The data byte frame is split into data bytes,
as shown in Figure 45.
LIN Frame Data Transmission and Reception
When the break symbol and synchronization bytes have been
correctly received, data is transmitted and received via the
COMTX and COMRX MMRs, after configuration of the UART
to the required baud rate.
Configuring the UART for use with LIN requires the use of the
following UART MMRs:
COMDIV0: divisor latch (low byte)
COMDIV1: divisor latch (high byte)
COMDIV2: 16-bit fractional baud divide register
The required values for COMDIV0, COMDIV1 and COMDIV2
are derived from the LHSVAL0, to generate the required baud rate.
COMCON0 is a line control register. When the UART is
correctly configured, the LIN protocol for receiving and
transmitting data is identical to the UART specification.
Managing data on the LIN bus requires the use of the following
UART MMRs:
COMTX: 8-bit transmit register
COMRX: 8-bit receive register
COMCON0: line control register
COMSTA0: line status register
Transmitting data on the LIN bus requires that the relevant data
be placed into COMTX. Reading data received on the LIN bus
requires the monitoring of COMRX. To ensure that data is
received or transmitted correctly, COMSTA0 is monitored.
For more information, see the UART Serial Interface section.
Under software control, it is possible to multiplex the UART
data lines (TxD and RxD) to external GPIO pins (GPIO_7 and
GPIO_8). For more information, see the description of the
GPIO Port1 Control Register (GP1CON).
相关PDF资料 |
PDF描述 |
|---|---|
| AT91R40008-66AU-999 | IC MCU 32BIT RISC 100LQFP |
| ADUC7024BSTZ62-RL | IC MCU 12BIT 1MSPS UART 64-LQFP |
| VE-B33-IW-F3 | CONVERTER MOD DC/DC 24V 100W |
| VE-B33-IW-F1 | CONVERTER MOD DC/DC 24V 100W |
| VE-B34-IX-F3 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7032BSTZ-8L | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays |
| ADUC7032BSTZ-8L-RL | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel |
| ADUC7032BSTZ-8V | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| ADUC7032BSTZ-8V-RL | 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| ADUC7033 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
发布紧急采购，3分钟左右您将得到回复。