- 您现在的位置：买卖IC网 > PDF目录11203 > ADUC7032BSTZ-88-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LQFP PDF资料下载
参数资料
| 型号： | ADUC7032BSTZ-88-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 56/120页 |
| 文件大小： | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LQFP |
| 标准包装： | 2,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI，UART/USART |
| 外围设备： | POR，PSM，温度传感器，WDT |
| 输入/输出数： | 9 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页当前第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页
ADuC7032-8L
Rev. A | Page 40 of 120
VOLTAGE CHANNEL ADC (V-ADC)
The V-ADC is intended to convert battery voltage. As with the
current channel ADC, described in the Current Channel ADC
(I-ADC) section, this ADC employs an identical Σ-Δ conversion
technique, including a modified Sinc3 low-pass filter to give
a valid 16-bit data conversion result at programmable output
rates from 4 Hz to 8 kHz. An external RC filter network is not
required because this is implemented internally in the voltage
channel.
The external battery voltage (VBAT) is routed to the ADC input
via an on-chip high voltage, resistive attenuator. This must be
enabled/disabled via HVCFG1[7].
The time to a first valid (fully settled) result on the voltage
channel is three ADC conversion cycles with chop mode turned
off, and two ADC conversion cycles with chop mode turned on.
This ADC is again buffered, but, unlike the current channel,
it has a fixed VBAT input range of 0 V to 28.8 V (assuming an
internal 1.2 V reference). A top level overview of this ADC
signal chain is shown in Figure 16.
TEMPERATURE CHANNEL ADC (T-ADC)
The T-ADC is designed to convert battery temperature. The
battery temperature can be derived via the on-chip temperature
sensor or an external temperature sensor input.
The time to a first valid (fully settled) result after an input
channel switch on the temperature channel is three ADC
conversion cycles with chop mode turned off and two ADC
conversion cycles with chop mode turned on.
As with the current and voltage channel ADCs, this ADC uses
an identical Σ-Δ conversion technique, including a modified
Sinc3 low-pass filter to give a valid 16-bit data conversion result
at programmable output rates from 4 Hz to 8 kHz.
05
98
6-
0
16
ADC
RESULT
OUTPUT
FORMAT
CHOP
Σ- ADC
THE
Σ-
ARCHITECTURE
ENSURES 16 BITS
NO MISSING CODES.
OUTPUT AVERAGE
AS PART OF THE CHOPPING
IMPLEMENTATION, EACH
DATA-WORD OUTPUT FROM
THE FILTER IS SUMMED AND
AVERAGED WITH ITS
PREDECESSOR.
Σ- MODULATOR
THE MODULATOR PROVIDES A
HIGH FREQUENCY 1-BIT DATA
STREAM (THE OUTPUT OF
WHICH IS ALSO CHOPPED) TO
THE DIGITAL FILTER, THE DUTY
CYCLE OF WHICH REPRESENTS
THE SAMPLED ANALOG INPUT
VOLTAGE.
Σ- ADC
Σ-
MODULATOR
PROGRAMMABLE
DIGITAL FILTER
OUTPUT
AVERAGE
OFFSET
COEFFICIENT
GAIN
COEFFICIENT
ADC INTERRUPT GENERATOR
GENERATES AN ADC
INTERRUPT ONCE A VOLTAGE
CONVERSION IS COMPLETE.
PRECISION REFERENCE
THE INTERNAL 5ppm/°C
REFERENCE IS ROUTED TO
THE ADC BY DEFAULT. AN
EXTERNAL REFERENCE ON
THE VREF PIN CAN ALSO
BE SELECTED.
BUF
CHOP
INTERNAL
REFERENCE
VREF
PROGRAMMABLE
DIGITAL FILTER
THE SINC3 FILTER REMOVES
QUANTIZATION NOISE INTRODUCED
BY THE MODULATOR. THE UPDATE
RATE AND BANDWIDTH OF THIS
FILTER ARE PROGRAMMABLE VIA
THE ADCFLT MMR.
OUTPUT SCALING
THE OUTPUT WORD FROM
THE DIGITAL FILTER IS
SCALED BY THE CALIBRATION
COEFFICIENTS BEFORE BEING
PROVIDED AS THE
CONVERSION RESULT.
VBAT
45R*
2R*
1R*
ADC
INTERRUPT
DIFFERENTIAL
ATTENUATOR
DIVIDE BY 24, INPUT
ATTENUATOR.
BUFFER AMPLIFIERS
THE BUFFER AMPLIFIERS
PRESENT A HIGH
IMPEDANCE INPUT STAGE
FOR THE ANALOG INPUT.
ANALOG INPUT
PROGRAMMABLE CHOPPING
THE INPUTS ARE
ALTERNATELY REVERSED
THROUGH THE
CONVERSION CYCLE.
VOLTAGE
DATA MMR
*R = 60k
Figure 16. Voltage ADC, Top Level Overview
相关PDF资料 |
PDF描述 |
|---|---|
| AT91R40008-66AU-999 | IC MCU 32BIT RISC 100LQFP |
| ADUC7024BSTZ62-RL | IC MCU 12BIT 1MSPS UART 64-LQFP |
| VE-B33-IW-F3 | CONVERTER MOD DC/DC 24V 100W |
| VE-B33-IW-F1 | CONVERTER MOD DC/DC 24V 100W |
| VE-B34-IX-F3 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7032BSTZ-8L | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays |
| ADUC7032BSTZ-8L-RL | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel |
| ADUC7032BSTZ-8V | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| ADUC7032BSTZ-8V-RL | 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| ADUC7033 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
发布紧急采购，3分钟左右您将得到回复。