- 您现在的位置：买卖IC网 > PDF目录11203 > ADUC7032BSTZ-88-RL (Analog Devices Inc)IC MCU 96K FLASH DUAL 48LQFP PDF资料下载
参数资料
| 型号： | ADUC7032BSTZ-88-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 68/120页 |
| 文件大小： | 0K |
| 描述： | IC MCU 96K FLASH DUAL 48LQFP |
| 标准包装： | 2,000 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 连通性： | LIN，SPI，UART/USART |
| 外围设备： | POR，PSM，温度传感器，WDT |
| 输入/输出数： | 9 |
| 程序存储器容量： | 96KB（48K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.5K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 数据转换器： | A/D 2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 105°C |
| 封装/外壳： | 48-LQFP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页
ADuC7032-8L
Rev. A | Page 51 of 120
ADC Configuration Register
Name:
ADCCFG
Address:
0xFFFF051C
Default Value:
0x00
Access:
Read/write
Function:
The 8-bit ADC configuration MMR controls extended functionality related to the on-chip ADCs.
Table 43. ADCCFG MMR Bit Designations
Bit
Description
7
Analog Ground Switch Enable.
Set to 1 by user software to connect the external GND_SW pin (Pin 15) to an internal analog ground reference point. This bit
can be used to connect and disconnect external circuits and components to ground under program control and thereby
minimize dc current consumption when the external circuit or component is not being used. This bit is used in conjunction
with ADCMDE[6] to select a 20 kΩ resistor to ground.
6 to 5
Current Channel (32-Bit) Accumulator Enable.
00 = accumulator disabled and reset to 0. The accumulator must be disabled for a full ADC conversion, (ADCSTA[0] set twice)
before the accumulator can be re-enabled to ensure the accumulator is reset.
01 = accumulator active.
Positive current values are added to the accumulator total. The accumulator can overflow if allowed to run for >65,535 conversions.
Negative current values are subtracted from the accumulator total. The accumulator is clamped to a minimum value of 0.
10 = accumulator active.
Positive current values are added to the accumulator total. The accumulator can overflow if allowed to run for >65,535 conversions.
The absolute values of negative current are subtracted from the accumulator total. In this mode, the accumulator continues
to accumulate negatively, below 0.
11 = accumulator and accumulator comparator enabled. This mode is the same as Mode 10 but with the accumulator
comparator enabled.
4 to 3
Current Channel ADC Comparator Enable.
00 = comparator disabled.
01 = comparator active, interrupt asserted if absolute value of I-ADC conversion result |I| ≥ ADC0TH.
10 = comparator-count mode active, interrupt asserted if the absolute value of an I-ADC conversion result |I| ≥ ADC0TH for
number of ADC0TCL conversions; conversion value |I| < ADC0TH resets the threshold counter value (ADC0THV) to 0.
11 = comparator-count mode active, interrupt asserted if absolute value of an I-ADC conversion result |I| ≥ ADC0TH for
number of ADC0TCL conversions; conversion value |I| < ADC0TH decrements the threshold counter value (ADC0THV) towards 0.
2
Current Channel ADC Overrange Enable.
Set by user to enable a coarse comparator on the current channel ADC. If the current reading is grossly (>30% approximate)
overranged for the active gain setting, then the overrange bit in the ADCSTA MMR is set. For the flag to be set, the current
must be outside this range for >125 μs. This feature should not be used in ADC low power mode.
1
ADC FIFO Enable.
Set to 1 by user code to enable ADC FIFO on current and voltage ADC channels. The FIFO function allows up to 32 current
and voltage ADC results to be stored in an on-chip FIFO. The current status of the FIFO is reflected by three bits in the ADCSTA
register. If more than 32 results are stored in the FIFO, the contents of the FIFO may be corrupted.
0
Current Channel ADC, Result Counter Enable.
Set by user to enable the result count mode. In this mode, an I-ADC interrupt is generated only when ADC0RCV =
ADC0RCL. This allows the I-ADC to continuously monitor current but interrupt the MCU core only after a defined
number of conversions. Note that unless the ADC FIFO is enabled (ADCCNG[1] = 1), only the last conversion value is
available (intermediate I-ADC conversion results are not stored) when the ADC counter interrupt occurs. The voltage
and temperature ADCs also continue to convert if enabled, but again, only the last conversion result is available
(intermediate V-ADC and T-ADC conversion results are not stored) when the ADC counter interrupt occurs.
相关PDF资料 |
PDF描述 |
|---|---|
| AT91R40008-66AU-999 | IC MCU 32BIT RISC 100LQFP |
| ADUC7024BSTZ62-RL | IC MCU 12BIT 1MSPS UART 64-LQFP |
| VE-B33-IW-F3 | CONVERTER MOD DC/DC 24V 100W |
| VE-B33-IW-F1 | CONVERTER MOD DC/DC 24V 100W |
| VE-B34-IX-F3 | CONVERTER MOD DC/DC 48V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7032BSTZ-8L | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays |
| ADUC7032BSTZ-8L-RL | 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel |
| ADUC7032BSTZ-8V | 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述: |
| ADUC7032BSTZ-8V-RL | 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR) |
| ADUC7033 | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive |
发布紧急采购，3分钟左右您将得到回复。