收藏本站
参数资料
型号： ADUC7032BSTZ-88-RL
厂商： Analog Devices Inc
文件页数： 59/120页
文件大小： 0K
描述： IC MCU 96K FLASH DUAL 48LQFP
标准包装： 2,000
系列： MicroConverter® ADuC7xxx
核心处理器： ARM7
芯体尺寸： 16/32-位
速度： 20.48MHz
连通性： LIN，SPI，UART/USART
外围设备： POR，PSM，温度传感器，WDT
输入/输出数： 9
程序存储器容量： 96KB（48K x 16）
程序存储器类型： 闪存
RAM 容量： 1.5K x 32
电压 - 电源 (Vcc/Vdd)： 3.5 V ~ 18 V
数据转换器： A/D 2x16b
振荡器型： 内部
工作温度： -40°C ~ 105°C
封装/外壳： 48-LQFP
包装： 带卷 (TR)
ADuC7032-8L
Rev. A | Page 43 of 120
ADC MMR INTERFACE
The ADC is controlled and configured via a number of MMRs
that are described in detail on the following pages.
All bits defined in the top eight MSBs (Bit 8 to Bit 15) of the
ADCSTA MMR (see Table 35) are used as flags only and do not
generate interrupts. All bits defined in the lower eight LSBs (Bit
0 to Bit 7) of this MMR are logic OR’ed to produce a single ADC
interrupt to the MCU core.
In response to an ADC interrupt, user code should interrogate
the ADCSTA MMR to determine the source of the interrupt.
Each ADC interrupt source can be individually masked via the
ADCMSKI MMR, as described in the ADC Interrupt Source
Enable Register section.
All ADC result-ready bits are cleared by a read of the ADC0DAT
MMR. If the current channel ADC is not enabled, all ADC
result-ready bits are cleared by a read of the ADC1DAT or
ADC2DAT MMRs.
To ensure that I-ADC, V-ADC, and T-ADC conversion data is
synchronous, user code should first read the ADC2DAT/
ADC1DAT MMRs and then the ADC0DAT MMR. New ADC
conversion results are not written to the ADCxDAT MMRs
unless the respective ADC result-ready bits are first cleared.
The only exception to this rule is data conversion result updates
when the ARM core is powered down. In this mode, ADCxDAT
registers always contain the most recent ADC conversion results,
even though the ready bits have not been cleared.
ADC Status Register
Name:
ADCSTA
Address:
0xFFFF0500
Default Value:
0x0000
Access:
Read only
Function:
This register holds general status information related to the mode of operation or current status of the ADuC7032-8L ADCs.
Table 35. ADCSTA MMR Bit Designations
Bit
Description
15
ADC Calibration Status.
Set automatically in hardware to indicate that an ADC calibration cycle has been completed.
Cleared after ADCMDE is written to.
14
ADC Temperature Conversion Error.
Set automatically in hardware to indicate that a temperature conversion overrange or underrange has occurred. The conversion
result is clamped to negative full scale (underrange error) or positive full scale (overrange error) in this case.
Cleared when a valid (in-range) temperature conversion result is written to the ADC2DAT register.
13
ADC Voltage Conversion Error.
Set automatically in hardware to indicate that a voltage conversion overrange or underrange has occurred. The conversion result
is clamped to negative full scale (underrange error) or positive full scale (overrange error) in this case.
Cleared when a valid (in-range) voltage conversion result is written to the ADC1DAT register.
12
ADC Current Conversion Error.
Set automatically in hardware to indicate that a current conversion overrange or underrange has occurred. The conversion result is
clamped to negative full scale (underrange error) or positive full scale (overrange error) in this case.
Cleared when a valid (in-range) current conversion result is written to the ADC0DAT register.
11
Not Used. Reserved for future functionality and should not be monitored by user code.
10
Not Used. Reserved for future functionality and should not be monitored by user code.
9
ADC FIFO Error Flag.
Set to 1 automatically to indicate that the FIFO has overflowed. This bit does not cause an interrupt but is latched high and can be
cleared only by disabling the FIFO or reconfiguring the ADC.
Reads 0 if the FIFO is disabled or if the FIFO has not overflowed.
8
ADC FIFO Empty Flag.
Set to 1 automatically to indicate the ADC FIFO is empty. It is a flag bit only and cannot generate an interrupt.
Reads 0 if the ADC FIFO is disabled.
7
ADC FIFO Full Flag.
Set to 1 automatically to indicate the ADC FIFO is full. Any subsequent I-ADC and V-ADC conversion results cause an overflow and
corrupt the ADC FIFO.
Cleared by disabling the FIFO or reconfiguring the ADC.
6
Accumulator Comparator Threshold Exceeded.
Indicates that the absolute value of the current channel accumulator has exceeded the programmed threshold.
Cleared by disabling the accumulator comparator function in ADCCFG[6:5] or by reconfiguring the ADC.
5
Not Used. Reserved for future functionality and should not be monitored by user code.
相关PDF资料
PDF描述
AT91R40008-66AU-999 IC MCU 32BIT RISC 100LQFP
ADUC7024BSTZ62-RL IC MCU 12BIT 1MSPS UART 64-LQFP
VE-B33-IW-F3 CONVERTER MOD DC/DC 24V 100W
VE-B33-IW-F1 CONVERTER MOD DC/DC 24V 100W
VE-B34-IX-F3 CONVERTER MOD DC/DC 48V 75W
相关代理商/技术参数
参数描述
ADUC7032BSTZ-8L 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Trays
ADUC7032BSTZ-8L-RL 制造商:Analog Devices 功能描述:FLASH 96K ARM7 TRIPLE 16-BIT ADC LIN IC. - Tape and Reel
ADUC7032BSTZ-8V 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
ADUC7032BSTZ-8V-RL 功能描述:IC BATTERY SENSOR PREC 48-LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:1,500 系列:AVR® ATtiny 核心处理器:AVR 芯体尺寸:8-位 速度:16MHz 连通性:I²C，LIN，SPI，UART/USART，USI 外围设备:欠压检测/复位，POR，PWM，温度传感器，WDT 输入/输出数:16 程序存储器容量:8KB（4K x 16） 程序存储器类型:闪存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 11x10b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:带卷 (TR)
ADUC7033 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Precision Battery Sensor For Automotive
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*