参数资料
| 型号： | CDB4245 |
| 厂商： | Cirrus Logic Inc |
| 文件页数： | 37/59页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR CS4245 CODEC |
| 标准包装： | 1 |
| 主要目的： | 音频编解码器 |
| 嵌入式： | 是，FPGA / CPLD |
| 已用 IC / 零件： | CS4245 |
| 主要属性： | 4 个单端模拟和 1 个麦克风输入和 8 个输出，S/PDIF 发射器和接收器 |
| 次要属性： | 图形用户界面 |
| 已供物品： | 板 |
| 产品目录页面： | 754 (CN2011-ZH PDF) |
| 相关产品： | CS4245-DQZR-ND - IC CODEC AUD STER 104DB 48-LQFP 598-1616-ND - IC CODEC AUD STER 104DB 48LQFP 598-1034-ND - IC CODEC AUD STER 104DB 48LQFP |
| 其它名称： | 598-1501 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
CS4245
signer to achieve idle channel noise/signal-to-noise ratios which are only limited by the external mute circuit.
The MUTEC pin is an active-low CMOS driver. See Figure 16 for a suggested active-low mute circuit.
+V EE
AOUT
LPF
AC
Couple
560 ?
Audio
Out
47 k ?
CS4245
-V EE
+V A
MMUN2111LT1
MUTEC
2 k ?
10 k ?
-V EE
Figure 16. Suggested Active-Low Mute Circuit
4.12
Control Port Description and Timing
The control port is used to access the registers, allowing the CS4245 to be configured for the desired oper-
ational modes and formats. The operation of the control port may be completely asynchronous with respect
to the audio sample rates. However, to avoid potential interference problems, the control port pins should
remain static if no operation is required.
The control port has two modes: SPI and I2C, with the CS4245 acting as a slave device. SPI Mode is se-
lected if there is a high-to-low transition on the AD0/CS pin, after the RESET pin has been brought high. I2C
Mode is selected by connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently
selecting the desired AD0 bit address state.
4.12.1 SPI Mode
In SPI Mode, CS is the CS4245 chip-select signal; CCLK is the control port bit clock (input into the CS4245
from the microcontroller); CDIN is the input data line from the microcontroller; CDOUT is the output data
line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling edge.
Figure 17 shows the operation of the control port in SPI Mode. To write to a register, bring CS low. The
first seven bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indi-
cator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP),
which is set to the address of the register that is to be updated. The next eight bits are the data that will
be placed into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z
state. It may be externally pulled high or low with a 47 k ? resistor, if desired.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. To begin a read, bring CS low, send out the chip ad-
DS656F3
37
相关PDF资料 |
PDF描述 |
|---|---|
| CDB42L55 | BOARD EVAL FOR CS42L55 CODEC |
| CDB44L11 | EVALUATION BOARD FOR CS44L11 |
| CDB48500-USB | KIT USB EVALUATION FOR CDB48500 |
| CDB5378 | EVALUATION BOARD FOR CS5378 |
| CDB5460AU | EVALUATION BOARD FOR CS5460A |
相关代理商/技术参数 |
参数描述 |
|---|---|
| CDB42518 | 功能描述:音频 IC 开发工具 Eval Bd RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB42528 | 功能描述:音频 IC 开发工具 Eval Bd RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB4265 | 功能描述:音频 IC 开发工具 Eval Bd 192kHz CODEC w/PGA & Input Mux RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB4270 | 功能描述:音频 IC 开发工具 Eval Bd 105dB 192kHz CODEC RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
| CDB4271 | 功能描述:音频 IC 开发工具 Eval Bd CS4271 RoHS:否 制造商:Texas Instruments 产品:Evaluation Kits 类型:Audio Amplifiers 工具用于评估:TAS5614L 工作电源电压:12 V to 38 V |
发布紧急采购，3分钟左右您将得到回复。