- 您现在的位置：买卖IC网 > PDF目录1914 > DS2152L+ (Maxim Integrated Products)IC TXRX T1 1CHIP ENHNCD 100-LQFP PDF资料下载
参数资料
| 型号： | DS2152L+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/97页 |
| 文件大小： | 0K |
| 描述： | IC TXRX T1 1CHIP ENHNCD 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 功能： | 单芯片收发器 |
| 接口： | T1 |
| 电路数： | 1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 电流 - 电源： | 75mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 管件 |
| 包括： | DSX-1 和 CSU 线路补偿发生器，HDLC 控制器，带内回路代码发生器和检测器 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
DS2152
31 of 97
5 STATUS AND INFORMATION REGISTERS
There is a set of nine registers that contain information on the current real-time status of the DS2152:
Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Registers 1 to 3
(RIR1/RIR2/RIR3), and a set of four registers for the on-board HDLC and BOC controller for the FDL.
The specific details on the four registers pertaining to the FDL are covered in Section 12.1, but they
operate the same as the other status registers in the DS2152, described below.
When a particular event has occurred (or is occurring), the appropriate bit in one of these nine registers is
set to 1. All the bits in SR1, SR2, RIR1, RIR2, and RIR3 registers operate in a latched fashion. This
means that if an event or an alarm occurs and a bit is set to 1 in any of the registers, it remains set until the
user reads that bit. The bit is cleared when it is read and it is not set again until the event has occurred
again (or in the case of the RBL, RYEL, LRCL, and RLOS alarms, the bit remains set if the alarm is still
present). The bits in the four FDL status registers that are not latched are listed in Section 12.1.
The user will always precede a read of any of the nine registers with a write. The byte written to the
register will inform the DS2152 which bits the user wishes to read and have cleared. The user will write a
byte to one of these registers, with a 1 in the bit positions he or she wishes to read and a 0 in the bit
positions he or she does not wish to obtain the latest information on. When a 1 is written to a bit location,
the read register will be updated with the latest information. When a 0 is written to a bit position, the read
register will not be updated and the previous value will be held. A write to the status and information
registers will be immediately followed by a read of the same register. The read result should be logically
ANDed with the mask byte that was just written, and this value should be written back into the same
register to ensure that bit does indeed clear. This second write step is necessary because the alarms and
events in the status registers occur asynchronously in respect to their access via the parallel port. This
write-read-write scheme allows an external microcontroller or microprocessor to individually poll certain
bits without disturbing the other bits in the register. This operation is key in controlling the DS2152 with
higher-order software languages.
The SR1, SR2, and FDLS registers have the unique ability to initiate a hardware interrupt via the INT
output pin. Each of the alarms and events in the SR1, SR2, and FDLS can be either masked or unmasked
from the interrupt pin via the Interrupt Mask Register 1 (IMR1), Interrupt Mask Register 2 (IMR2), and
FDL Interrupt Mask Register (FIMR) respectively. The FIMR register is covered in Section 12.1.
The interrupts caused by alarms in SR1 (namely RYEL, LRCL, RBL, and RLOS) act differently than the
interrupts caused by events in SR1 and SR2 (namely LUP, LDN, LOTC, RSLIP, RMF, TMF, SEC,
RFDL, TFDL, RMTCH, RAF, and RSC) and FIMR. The alarm caused interrupts will force the INT pin
low whenever the alarm changes state (i.e., the alarm goes active or inactive according to the set/clear
criteria in Table 5-2). The INT pin will be allowed to return high (if no other interrupts are present) when
the user reads the alarm bit that caused the interrupt to occur even if the alarm is still present.
The event caused interrupts will force the INT pin low when the event occurs. The INT pin will be
allowed to return high (if no other interrupts are present) when the user reads the event bit that caused the
interrupt to occur.
相关PDF资料 |
PDF描述 |
|---|---|
| DS2153Q-A7+T&R | IC TXRX E1 1-CHIP 5V 44-PLCC |
| DS2154LNA2+ | IC TXRX E1 5V 100-LQFP |
| DS2154L | IC TXRX E1 1CHIP 5V ENH 100-LQFP |
| DS2155LN | IC TXRX T1/E1/J1 1-CHIP 100-LQFP |
| DS2156LN+ | IC TXRX T1/E1/J1 1-CHIP 100-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2152L+ | 功能描述:网络控制器与处理器 IC Enhanced T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152L-ES | 制造商:DALL 功能描述: |
| DS2152LN | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152LN+ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2153DK | 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。