- 您现在的位置：买卖IC网 > PDF目录1914 > DS2152L+ (Maxim Integrated Products)IC TXRX T1 1CHIP ENHNCD 100-LQFP PDF资料下载
参数资料
| 型号： | DS2152L+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 54/97页 |
| 文件大小： | 0K |
| 描述： | IC TXRX T1 1CHIP ENHNCD 100-LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 90 |
| 功能： | 单芯片收发器 |
| 接口： | T1 |
| 电路数： | 1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 电流 - 电源： | 75mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP |
| 供应商设备封装： | 100-LQFP（14x14） |
| 包装： | 管件 |
| 包括： | DSX-1 和 CSU 线路补偿发生器，HDLC 控制器，带内回路代码发生器和检测器 |
| 产品目录页面： | 1429 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
DS2152
58 of 97
Like the other status registers in the DS2152, the user will always precede a read of any of the four
registers with a write. The byte written to the register will inform the DS2152 which of the latched bits
the user wishes to read and have cleared (the real-time bits are not affected by writing to the status
register). The user will write a byte to one of these registers, with a 1 in the bit positions he or she wishes
to read and a 0 in the bit positions he or she does not wish to obtain the latest information on. When a 1 is
written to a bit location, the read register will be updated with current value and it will be cleared. When a
0 is written to a bit position, the read register will not be updated and the previous value will be held. A
write to the status and information registers will be immediately followed by a read of the same register.
The read result should be logically ANDed with the mask byte that was just written and this value should
be written back into the same register to insure that bit does indeed clear. This second write step is
necessary because the alarms and events in the status registers occur asynchronously in respect to their
access via the parallel port. This write-read-write (for polled driven access) or write-read (for interrupt-
driven access) scheme allows an external microcontroller or microprocessor to individually poll certain
bits without disturbing the other bits in the register. This operation is key in controlling the DS2152 with
higher-order software languages.
Like the SR1 and SR2 status registers, the FDLS register has the unique ability to initiate a hardware
interrupt via the
INT output pin. Each of the events in the FDLS can be either masked or unmasked from
the interrupt pin via the FDL Interrupt Mask Register (FIMR). Interrupts will force the
INT pin low when
the event occurs. The
INT pin will be allowed to return high (if no other interrupts are present) when the
user reads the event bit that caused the interrupt to occur.
12.1.2 Basic Operation Details
To allow the DS2152 to properly source/receive data from/to the HDLC and BOC controller the legacy
FDL circuitry (which is described in Section 12.2) should be disabled and the following bits should be
programmed as shown:
TCR1.2 = 1 (source FDL data from the HDLC and BOC controller)
TBOC.6 = 1 (enable HDLC and BOC controller)
CCR2.5 = 0 (disable SLC-96 and D4 Fs-bit insertion)
CCR2.4 = 0 (disable legacy FDL 0 stuffer)
CCR2.1 = 0 (disable SLC-96 reception)
CCR2.0 = 0 (disable legacy FDL 0 stuffer)
IMR2.4 = 0 (disable legacy receive FDL buffer full interrupt)
IMR2.3 = 0 (disable legacy transmit FDL buffer empty interrupt)
IMR2.2 = 0 (disable legacy FDL match interrupt)
IMR2.1 = 0 (disable legacy FDL abort interrupt)
As a basic guideline for interpreting and sending both HDLC messages and BOC messages, the following
sequences can be applied:
相关PDF资料 |
PDF描述 |
|---|---|
| DS2153Q-A7+T&R | IC TXRX E1 1-CHIP 5V 44-PLCC |
| DS2154LNA2+ | IC TXRX E1 5V 100-LQFP |
| DS2154L | IC TXRX E1 1CHIP 5V ENH 100-LQFP |
| DS2155LN | IC TXRX T1/E1/J1 1-CHIP 100-LQFP |
| DS2156LN+ | IC TXRX T1/E1/J1 1-CHIP 100-LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS2152L+ | 功能描述:网络控制器与处理器 IC Enhanced T1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152L-ES | 制造商:DALL 功能描述: |
| DS2152LN | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2152LN+ | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS2153DK | 功能描述:KIT DESIGN TXRX E1 DS2153 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
发布紧急采购，3分钟左右您将得到回复。