- 您现在的位置：买卖IC网 > PDF目录16264 > DS21Q59DK (Maxim Integrated Products)KIT DESIGN FOR DS21Q59 PDF资料下载
参数资料
| 型号： | DS21Q59DK |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/76页 |
| 文件大小： | 0K |
| 描述： | KIT DESIGN FOR DS21Q59 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 主要目的： | 电信，调帧器和线路接口装置（LIU） |
| 已用 IC / 零件： | DS21Q59 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
DS21Q59 Quad E1 Transceiver
18 of 76
8.1 Power-Up Sequence
On power-up and after the supplies are stable, the DS21Q59 should be configured for operation by writing to all the
internal registers (this includes setting the test register to 00h) since the contents of the internal registers cannot be
predicted on power-up. The LIRST (CCR5.4) should be toggled from 0 to 1 to reset the line interface circuitry. (It
takes the device about 40ms to recover from the LIRST bit being toggled.) After the SYSCLK input is stable, the
ESR bits (CCR4.5 and CCR4.6) should be toggled from 0 to 1 (this step can be skipped if the elastic store is
disabled).
Register Name:
RCR
Register Description:
Receive Control Register
Register Address:
10 Hex
Bit #
7
6
5
4
3
2
1
0
Name
RSMF
RSM
RSIO
RESE
—
FRC
SYNCE
RESYNC
NAME
BIT
FUNCTION
RSMF
7
RSYNC Multiframe Function. Only used if the RSYNC pin is programmed in the
multiframe mode (RCR.6 = 1).
0 = RSYNC outputs CAS multiframe boundaries.
1 = RSYNC outputs CRC4 multiframe boundaries.
RSM
6
RSYNC Mode Select
0 = frame mode (see the timing diagrams in Section 24.1)
1 = multiframe mode (see the timing diagrams in Section 24.1)
RSIO
5
RSYNC I/O Select. (Note: This bit must be set to 0 when RCR .4 = 0.)
0 = RSYNC is an output (depends on RCR.6)
1 = RSYNC is an input (only valid if elastic store enabled)
RESE
4
Receive Elastic Store Enable
0 = elastic store is bypassed
1 = elastic store is enabled
—
3
Unused. Should be set = 0 for proper operation.
FRC
2
Frame Resync Criteria
0 = resync if FAS received in error three consecutive times
1 = resync if FAS or bit 2 of non-FAS is received in error three consecutive times
SYNCE
1
Sync Enable
0 = auto resync enabled
1 = auto resync disabled
RESYNC
0
Resync. When toggled from low to high, a resync is initiated. Must be cleared and
set again for a subsequent resync.
相关PDF资料 |
PDF描述 |
|---|---|
| RCM28DCTH | CONN EDGECARD 56POS DIP .156 SLD |
| EET-ED2D152EA | CAP ALUM 1500UF 200V 20% SNAP |
| RCM28DCTD | CONN EDGECARD 56POS DIP .156 SLD |
| PLE0G681MDO1 | CAP ALUM 680UF 4V 20% RADIAL |
| PLE0E561MCO1 | CAP ALUM 560UF 2.5V 20% RADIAL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21Q59L | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q59L+ | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q59LN | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q59LN+ | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21S07A | 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。