- 您现在的位置：买卖IC网 > PDF目录97869 > DS3134 (DALLAS SEMICONDUCTOR) DATACOM, FRAMER, PBGA256 PDF资料下载
参数资料
| 型号： | DS3134 |
| 厂商： | DALLAS SEMICONDUCTOR |
| 元件分类： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PBGA256 |
| 封装： | 27 X 27 MM, PLASTIC, BGA-256 |
| 文件页数： | 13/203页 |
| 文件大小： | 777K |
| 代理商： | DS3134 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页
DS3134
11 of 203
In the receive path, the following process occurs. The HDLC Engines collect the incoming data into
32-bit dwords and then signal the FIFO that the engine has data to transfer to the FIFO. The 16 ports are
priority decoded (Port 0 gets the highest priority) for the transfer of data from the HDLC Engines to the
FIFO Block. Please note that in a channelized application, a single port may contain up to 128 HDLC
channels and since HDLC channel numbers can be assigned randomly, the HDLC channel number has no
bearing on the priority of this data transfer. This situation is of no real concern however since the
DS3134 has been designed to handle up to 104 Mbps in both the receive and transmit directions without
any potential loss of data due to priority conflicts in the transfer of data from the HDLC Engines to the
FIFO and vice versa.
The FIFO transfers data from the HDLC Engines into the FIFO and checks to see if the FIFO has filled to
beyond the programmable High Water Mark. If it has, then the FIFO signals to the DMA that data is
ready to be burst read from the FIFO to the PCI Bus. The FIFO Block controls the DMA Block and it
tells the DMA when to transfer data from the FIFO to the PCI Bus. Since the DS3134 can handle
multiple HDLC channels, it is quite possible that at any one time, several HDLC channels will need to
have data transferred from the FIFO to the PCI Bus. The FIFO determines which HDLC channel the
DMA will handle next via a Host configurable algorithm, which allows the selection to be either round
robin or priority, decoded (with HDLC Channel 1 getting the highest priority).
Depending on the
application, the selection of this algorithm can be quite important. The DS3134 cannot control when it
will be granted PCI Bus access and if bus access is restricted, then the Host may wish to prioritize which
HDLC channels get top priority access to the PCI Bus when it is granted to the DS3134.
When the DMA transfers data from the FIFO to the PCI Bus, it burst reads all available data in the FIFO
(even if the FIFO contains multiple HDLC packets) and tries to empty the FIFO. If an incoming HDLC
packet is not large enough to fill the FIFO to the High Water Mark, then the FIFO will not wait for more
data to enter the FIFO, it will signal the DMA that a End Of Frame (EOF) was detected and that data is
ready to be transferred from the FIFO to the PCI Bus by the DMA.
In the transmit path, a very similar process occurs. As soon as a HDLC channel is enabled, the HDLC
(Layer 2) Engines begin requesting data from the FIFO. Like the receive side, the 16 ports are priority
decoded with Port 0 getting the highest priority. Hence, if multiple ports are requesting packet data, the
FIFO will first satisfy the requirements on all the enabled HDLC channels in the lower numbered ports
before moving on to the higher numbered ports. Again there is no potential loss of data as long as the
transmit throughput maximum of 104 Mbps is not exceeded. When the FIFO detects that a HDLC Engine
needs data, it then transfers the data from the FIFO to the HDLC Engines in 8-bit chunks. If the FIFO
detects that the FIFO is below the Low Water Mark, it then checks with the DMA to see if there is any
data available for that HDLC Channel. The DMA will know if any data is available because the Host on
the PCI Bus will have informed it of such via the Pending Queue Descriptor. When the DMA detects that
data is available, it informs the FIFO and then the FIFO decides which HDLC channel gets the highest
priority to the DMA to transfer data from the PCI Bus into the FIFO. Again, since the DS3134 can handle
multiple HDLC channels, it is quite possible that at any one time, several HDLC channels will need the
DMA to burst data from the PCI Bus into the FIFO. The FIFO determines which HDLC channel the
DMA will handle next via a Host configurable algorithm, which allows the selection to be either round
robin or priority, decoded (with HDLC Channel 1 getting the highest priority).
相关PDF资料 |
PDF描述 |
|---|---|
| DS3150QN | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150Q | DATACOM, PCM TRANSCEIVER, PQCC28 |
| DS3150TN | DATACOM, PCM TRANSCEIVER, PDIP48 |
| DS3150T | DATACOM, PCM TRANSCEIVER, PQFP48 |
| DS5000FP-12 | 8-BIT, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS-313PIN | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog Miscellaneous |
| DS-313-PIN | 功能描述:信号调节 RoHS:否 制造商:EPCOS 产品:Duplexers 频率:782 MHz, 751 MHz 频率范围: 电压额定值: 带宽: 阻抗:50 Ohms 端接类型:SMD/SMT 封装 / 箱体:2.5 mm x 2 mm 工作温度范围:- 30 C to + 85 C 封装:Reel |
| DS31400 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:8-Input, 14-Output, Dual DPLL Timing IC with Sub-ps Output Jitter |
| DS31400DK | 功能描述:时钟和定时器开发工具 DS31400 Dev Kit RoHS:否 制造商:Texas Instruments 产品:Evaluation Modules 类型:Clock Conditioners 工具用于评估:LMK04100B 频率:122.8 MHz 工作电源电压:3.3 V |
| DS31400GN | 功能描述:计时器和支持产品 Not Available From Mouser RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。