参数资料
型号: DSP56303VL100B1
厂商: Freescale Semiconductor
文件页数: 95/108页
文件大小: 0K
描述: IC DSP 24BIT 100MHZ 196-BGA
标准包装: 630
系列: DSP563xx
类型: 定点
接口: 主机接口,SSI,SCI
时钟速率: 100MHz
非易失内存: ROM(576 B)
芯片上RAM: 24kB
电压 - 输入/输出: 3.30V
电压 - 核心: 3.30V
工作温度: -40°C ~ 100°C
安装类型: 表面贴装
封装/外壳: 196-LBGA
供应商设备封装: 196-MAPBGA(15x15)
包装: 托盘
Power Consumption Considerations
DSP56303 Technical Data, Rev. 11
Freescale Semiconductor
4-3
Consider all device loads as well as parasitic capacitance due to PCB traces when you calculate
capacitance. This is especially critical in systems with higher capacitive loads that could create higher
transient currents in the VCC and GND circuits.
All inputs must be terminated (that is, not allowed to float) by CMOS levels except for the three pins with
internal pull-up resistors (TRST, TMS, DE).
Take special care to minimize noise levels on the VCCP, GNDP, and GNDP1 pins.
The following pins must be asserted after power-up: RESET and TRST.
If multiple DSP devices are on the same board, check for cross-talk or excessive spikes on the supplies due
to synchronous operation of the devices.
RESET
must be asserted when the chip is powered up. A stable EXTAL signal should be supplied before
deassertion of RESET.
At power-up, ensure that the voltage difference between the 5 V tolerant pins and the chip VCC never
exceeds 3.5 V.
4.3 Power Consumption Considerations
Power dissipation is a key issue in portable DSP applications. Some of the factors affecting current consumption
are described in this section. Most of the current consumed by CMOS devices is alternating current (ac), which is
charging and discharging the capacitances of the pins and internal nodes.
Current consumption is described by this formula:
Equation 3:
Where:
C
=
node/pin capacitance
V
=
voltage swing
f
=
frequency of node/pin toggle
Equation 4:
The maximum internal current (ICCImax) value reflects the typical possible switching of the internal buses on best-
case operation conditions—not necessarily a real application case. The typical internal current (ICCItyp) value
reflects the average switching of the internal buses on typical operating conditions.
Perform the following steps for applications that require very low current consumption:
1.
Set the EBD bit when you are not accessing external memory.
2.
Minimize external memory accesses, and use internal memory accesses.
3.
Minimize the number of pins that are switching.
4.
Minimize the capacitive load on the pins.
5.
Connect the unused inputs to pull-up or pull-down resistors.
Example 4-1. Current Consumption
For a Port A address pin loaded with 50 pF capacitance, operating at 3.3 V, with a 66 MHz clock, toggling at its maximum possible rate (33
MHz), the current consumption is expressed in Equation 4.
IC
V
f
×
=
I
50
10
12
×
3.3
×
33
×
10
6
×
5.48 mA
==
相关PDF资料
PDF描述
DSP56311VF150B1 IC DSP 24BIT 150MHZ 196-BGA
DSP56321VF200R2 IC DSP 24BIT 200MHZ 196-BGA
DSP56852VFE IC DSP 16BIT 120MHZ 81-MAPBGA
DSP56854FGE IC DSP 16BIT 120MHZ 128-LQFP
DSP56855BUE IC DSP 16BIT 120MHZ 100-LQFP
相关代理商/技术参数
参数描述
DSP56304GC66 制造商:未知厂家 制造商全称:未知厂家 功能描述:24-Bit Digital Signal Processor
DSP56304GC80 制造商:未知厂家 制造商全称:未知厂家 功能描述:24-Bit Digital Signal Processor
DSP56304PV66 制造商:未知厂家 制造商全称:未知厂家 功能描述:24-Bit Digital Signal Processor
DSP56304PV80 制造商:未知厂家 制造商全称:未知厂家 功能描述:24-Bit Digital Signal Processor
DSP56305DS 制造商:未知厂家 制造商全称:未知厂家 功能描述:DSP56305 Single Chip Channel Codec Digital Signal Processor Data Sheet