- 您现在的位置：买卖IC网 > PDF目录16860 > EVAL-AD7280AEDZ (Analog Devices Inc)BOARD EVAL FOR AD7280 PDF资料下载
参数资料
| 型号： | EVAL-AD7280AEDZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/48页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7280 |
| 标准包装： | 1 |
| 主要目的： | 电源管理，电池监控器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | * |
| 主要属性： | * |
| 次要属性： | SPI 接口 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页
AD7280A
EMC GUIDELINES
SCHEMATIC AND LAYOUT GUIDELINES
To optimize the performance of a chain of AD7280A devices
under noisy conditions—for example, when experiencing
electromagnetic interference—the following schematic and
layout guidelines should be observed (see Figure 29).
Note that these ferrite beads can be replaced with a small value
of resistance. The maximum value of resistance that can be
used is 20 Ω. A resistor should not be included on the V SS
line to the master chip. Instead, a direct connection should
be made from the battery cell connector to the V SS pin.
1.
All AD7280A devices in a daisy chain should be physically
Analog Devices, Inc., also recommends the following:
located on a single printed circuit board (PCB). Daisy-
chain connections between PCBs are not recommended.
Individual PCBs can be used for separate daisy chains. In
this case, however, communication between PCBs is via a
communication protocol such as SPI or CAN.
?
?
Inclusion of a 100 nF capacitor across the six individual cells
that are monitored by the AD7280A. This capacitor should
be placed physically close to the battery cell connector on
the PCB.
Correct termination of all unused pins on the device. More
2.
3.
4.
5.
6.
7.
Individual 22 pF capacitors should be placed on each
daisy-chain connection. The capacitors should be
terminated to either the V SS pin of the upper device or the
V DD pin of the lower device, depending on the direction in
which data is flowing in the daisy chain. The PD, CS,
SCLK, SDI, and CNVST daisy-chain connections pass data
up the chain. The 22 pF capacitors on these pins should be
terminated to the V SS pin of the upper device in the chain.
The SDOlo and ALERTlo daisy-chain connections pass
data down the chain. The 22 pF capacitors on these pins
should be terminated to the V DD pin of the lower device in
the chain.
A direct, low impedance trace should connect the V DD pin
of the lower device with the V SS pin of the upper device. The
AD7280A daisy-chain connections operate at the V DD /V SS
voltage of the adjacent AD7280As. Ensuring a low imped-
ance path between the supplies optimizes the performance
of the daisy-chain communications.
The application PCB should have a minimum of four
layers. The AD7280A daisy-chain connections should be
routed on an inner layer of the PCB.
The AD7280A daisy-chain connections should be shielded
above and below by a V SS supply plane connected to the V SS
pin of the upper device in the chain. The shield should extend
from the V SS and daisy-chain low pins of the upper device
(Pin 15, Pin 17, and Pin 21 to Pin 28) to cover the daisy-
chain high pins of the lower device (Pin 42 to Pin 48), as
well as a low impedance trace to the V DD pin. This shield
provides maximum protection to the daisy-chain connec-
tions when operating in a noisy environment.
The AD7280A devices should be placed as close together
as possible on the PCB to minimize the length of the daisy-
chain connections.
To minimize noise reaching the V DD /V SS pins of the
AD7280A, ferrite beads should be inserted into the V DD
and V SS supply traces coming from the battery. These beads
can be inserted into the PCB traces between the battery cell
connection on the PCB and the individual supply pins.
information about the correct termination of unused pins
Descriptions section.
OPERATION IN A NOISY ENVIRONMENT
When the AD7280A is operating in a noisy environment—for
example, when electromagnetic interference is experienced—
glitches can occur on the SPI or daisy-chain inputs and outputs.
To limit the effect that such glitches may have on the operation
of the AD7280A, each daisy-chain input is passed through a
filter before being applied internally within the device. The filter
on the PD pin is 130 μs wide (see the Power-Down section for
more information). The filter on the remaining daisy-chain
inputs ( CS, SCLK, SDI, CNVST, SDIhi, and ALERThi) is 150 ns
wide. Glitches wider than these values on any of the pins can
have an effect on the AD7280A, and care should be taken to
ensure correct operation.
Glitches that occur on the SCLK and CS pins can result in the
AD7280A losing synchronization with the DSP/microprocessor.
However, such a loss of synchronization affects only the 32-bit
word during which the glitch occurred. The AD7280A interface
is reset on the rising edge of CS to ensure that the part is resyn-
chronized, as described in the Serial Interface section.
Glitches that occur on the SDI or SDOhi pin can result in a
change of state of any of the bits in the 32-bit words that are
written to or read from the chain of AD7280As. In this event,
the 8-bit CRC received by the AD7280A or by the DSP/micro-
processor should not match the CRC that is calculated based
on the 32-bit word that was transmitted.
Glitches that occur on the ALERThi pin are observed on the
alert signal when output from the master device. Care should
be taken when designing the alert response software or hard-
ware to ensure that such glitches are treated appropriately in
the system.
Glitches that occur on the CNVST pin may be interpreted as a
conversion start request. If this occurs during a read operation,
it can result in incorrect data being read back from the AD7280A.
Rev. 0 | Page 44 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| V110C24C100B3 | CONVERTER MOD DC/DC 24V 100W |
| MLG0603S2N0S | INDUCTOR MULTILAYER 2.0NH 0201 |
| V110C24C100B2 | CONVERTER MOD DC/DC 24V 100W |
| EVAL-ADM1087EB | BOARD EVAL FOR ADM1087 |
| V110B28E150BG2 | CONVERTER MOD DC/DC 28V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-AD7291SDZ | 功能描述:BOARD EVAL FOR AD7291 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7292SDZ | 功能描述:数据转换 IC 开发工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| EVAL-AD7294EBZ | 功能描述:BOARD EVALUATION FOR AD7294 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7298SDZ | 功能描述:BOARD EVAL FOR AD7298 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
| EVAL-AD7298SDZ | 制造商:Analog Devices 功能描述:EVAL BOARD, AD7192 12BIT ADC |
发布紧急采购，3分钟左右您将得到回复。