参数资料
型号: GP2021
厂商: Mitel Networks Corporation
英文描述: GPS 12 channel Correlator Advance Information
中文描述: 全球定位系统12通道相关器研究进展信息
文件页数: 34/62页
文件大小: 372K
代理商: GP2021
4
GP2021
TYPICAL GPS RECEIVER
Fig. 2 shows a typical GPS receiver employing a GP2010
RF front–end, a GP2021 correlator and an ARM60 32 bit RISC
microprocessor.
A single front end may be used, since all GPS satellites use
the same L1 frequency of 1575.42 MHz. However, in order to
achieve better sky coverage, it is sometimes desirable to use
more than one antenna. In this case, separate front ends will
be needed.
The RF section, GP2010, performs down conversion of
the L1 signal for digital baseband processing. The resultant
signal is then correlated in the GP2021 with an internally
generated replica of the satellite code to be received.
Individual codes for each channel may be selected
independently to enable acquisition and tracking of up to 12
different satellites simultaneously
The results of the correlations form the accumulated data
and are transferred to the microprocessor to give the
broadcast satellite data (the ’Navigation Message’) and to
control the software signal tracking loops.
The GP2021 can be interfaced to one of two styles of front
end. In Real_Input mode, the front end supplies either a 1
(sign) or 2 (sign and magnitude) bit signal to either the
SIGN0/MAG0 or SIGN1/MAG1 inputs of the GP2021.
Alteratively, in Real_Input mode, 2 separate front ends can be
connected to a single GP2021 and selected under software
control. The GP2015 and GP2010 are Real_Input mode front
ends.
In Complex_Input mode, the front end is required to supply
In–phase (I) and Quadrature (Q) signals to the SIGN0/MAG0
and SIGN1/MAG1 inputs respectively. Hence, only a single
front end can be used with each GP2021 in Complex_Input
mode.
GP2010
SIGN
MAG
SAMPCLK
CLK_T
CLK_I
PLL_LOCK
10MHz
TCXO
TX/RX
SERIAL COMMS PORT
ACCUM_INT,MEAS_INT
12
CHANNEL
CORRELATOR
WREN
READ
MICRO_CLK
PERIPHERAL
FUNCTIONS
MEMORY
CONTROL
MEMORY
CONTROL
DATA
ADDR
ARM60
GP2021
L1 ANTENNA
Fig. 2 Block diagram of typical ARM based receiver
PIN DESCRIPTION
All V SS and V DD pins must be connected in order to ensure reliable operation. Any unused inputs must be tied High or Low.
The Table below describes the pin functions in Real_Input mode and assumes a master clock input frequency of 40MHz.
Those pins whose functions differ in Complex_Input mode are described at the end of the table.
Note that those pin names containing a ‘/’ have dual functionality between ARM System and Standard Interface modes. The
Pin mnemonic for ARM System mode always precedes the ‘/’.
Pin No
Signal Name
Type
Description ARM System Mode
Description Standard Interface
Mode
15, 35,
V SS
-
Ground Pin
56, 69,
72
14, 34,
V DD
+
Power supply to device.
55, 67,
74
1
MULTI_FN_IO
I/O
Multi–function input / output. Its function is configured by the IO_CONFIG register.
After a GP2021 reset it acts as the Digital System Test Enable input. It can also
be configured as a discrete output, or a discrete input if certain conditions are met.
Can be configured as the TRIGGER
input to the DEBUG block in ARM
System mode.
相关PDF资料
PDF描述
GRM40Y5V105Z16 Circular Connector; MIL SPEC:MIL-C-26482, Series I, Solder; Body Material:Aluminum; Series:PT06; No. of Contacts:21; Connector Shell Size:22; Connecting Termination:Solder; Circular Shell Style:Straight Plug; Body Style:Straight
GRM42-6X5R475K10 50/100M SOT-23 CMOS RF LDO REGULATORS
GT- 32090 Highly Integrated Single-Chip System Controller(高集成单片系统控制器)
GT-48001A Switched Ethernet Controller For 10BaseX(10BaseX交换式快速以太网控制器)
GT-48002A Switched Fast Ethernet Controller for 100BaseX(100BaseX交换式快速以太网控制器)
相关代理商/技术参数
参数描述
GP2021IGGQ1R 制造商:未知厂家 制造商全称:未知厂家 功能描述:Correlator
GP202K 制造商:GTM 制造商全称:GTM 功能描述:SURFACE MOUNT,SWITCHING DIODE
GP2030S 制造商:GTM 制造商全称:GTM 功能描述:N AND P-CHANNEL ENHANCEMENT MODE POWER MOSFET
GP2-031X250-50 制造商:GROOV-PIN 功能描述:
GP204 制造商:DEC 制造商全称:DEC 功能描述:2 AMP SOFT GLASS PASSIVATED DIODES