参数资料
| 型号： | IP-SLITE2 |
| 厂商： | Altera |
| 文件页数： | 45/110页 |
| 文件大小： | 0K |
| 描述： | IP SERIALLITE II |
| 标准包装： | 1 |
| 系列： | * |
| 类型： | MegaCore |
| 功能： | SerialLite II 协议 |
| 许可证： | 初始许可证 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
3–22
1
Chapter 3: Parameter Settings
Link Layer Configuration
The receiver Atlantic FIFO buffers include an end-of-packet based data available
feature which can be turned on by asserting the ctl_rxrdp_eopdav/ctl_rxhpp_eopdav
signals. The end-of-packet feature determines whether the dav remains high: if the
signal is asserted, and there is an end-of- packet beneath the FTL threshed, the dav
signal remains high until the end-of-packet is read out of the FIFO buffer. Otherwise,
if the signal is not asserted, the dav signal only remains high when the fill level of the
buffer is higher than the FTL value.
ctl_rxhpp_fth and ctl_rxrdp_fth are the threshold levels for the high priority and
regular data ports on the receiver Atlantic FIFO buffers. When the data fill level is
higher than the threshold level set by ctl_rxhpp_fth or ctl_rxrdp_fth , or dav = 1, it
means that there a large amount of data ready to be fetched at the FIFO buffer. You
must set these threshold levels based on your design requirements, and ensure that
the FIFO buffer does not underflow. You may also set the threshold levels to segment
size of a priority packet; or to the lowest level so that you can fetch data as soon as it is
stored in the FIFO buffer.
You can set ctl_rxhpp_ftl to 1 element unit so that it fetches the data from the RX
FIFO buffer as soon as there is data available. If you want to store some data before
fetching it, you can raise the threshold level.
The FIFO buffer threshold high ( ctl_txrdp_fth/ctl_txhpp_fth ) value for transmitter
variations controls when the txrdp_dav/txhpp_dav signals are asserted and
deasserted for the write side of the FIFO buffer, respectively. The txrdp_dav signal
indicates when there is room available to write new data into the FIFO buffer, and is
asserted when the fill level of the FIFO is less than the FTH setting, and deasserted
when the fill level of the FIFO is greater than the FTH.
For example, if FTH is five, and the fill level is four, the txrdp_dav/txhpp_dav signal is
high, indicating that the user can write data into the FIFO. If the fill level for this
example is six, the txrdp_dav/txhpp_dav signal is low, indicating that the user should
stop writing data into the FIFO.
ctl_txhpp_fth and ctl_txrdp_fth are the threshold levels for the high priority and
regular data ports on the transmitter Atlantic FIFO buffers. When the data fill level at
the FIFO buffer is lower than the threshold level set by ctl_txhpp_fth or
ctl_txrdp_fth , or dav = 1, it means that there are plenty of spaces available for data to
write into the buffer. You must set these threshold levels high so that the user logic
knows whenever the FIFO buffer has available spaces for data buffering and to ensure
that overflow does not occur. However, these threshold settings should not exceed the
FIFO depth.
For example, if the transmitter buffer size is 4,096 bytes, and the transmitter FIFO
depth is 2,048 element units, you should set the level of ctl_txhpp_fth to 250 element
units.
TSIZE = 2, and one FIFO element = 2 bytes
Maximum TX FIFO level (TX 8 lane) = 2,048/8 = 256 element units
You can set any value below 256 element units for ctl_txhpp_fth ; Altera
recommends a level of 250 element units or 8'hFA.
SerialLite II MegaCore Function
User Guide
January 2014 Altera Corporation
相关PDF资料 |
PDF描述 |
|---|---|
| IP-SRAM/QDRII | IP QDRII SRAM CONTROLLER |
| IP-VITERBI/SS | IP VITERBI LOW-SPEED |
| IP4220CZ6,125 | IC USB DUAL ESD PROTECT 6TSOP |
| IPA-66-1-600-10.0-A-01-T | CIRC BRKR 10A 2POLE SCREW TERM |
| IPR-CSC | IP COLOR SPACE CONVERTER RENEW |
相关代理商/技术参数 |
参数描述 |
|---|---|
| IPSLU-AP005-5 | 功能描述:Pressure Sensor 15 PSI (103.42 kPa) Absolute Male - 1/4" (6.35mm) NPT 4 mA ~ 20 mA Probe 制造商:cynergy 3 系列:IPSLU 零件状态:有效 压力类型:绝对 工作压力:15 PSI（103.42 kPa） 输出类型:模拟电流 输出:4 mA ~ 20 mA 精度:±0.5% 电压 - 电源:9 V ~ 32 V 端口尺寸:公型 - 1/4"（6.35mm） NPT 端口样式:有螺纹 特性:放大输出，温度补偿 端子类型:连接器 最高压力:- 工作温度:-20°C ~ 80°C 封装/外壳:探头组件 供应商器件封装:探头组件 标准包装:1 |
| IPSLU-AP010-5 | 功能描述:Pressure Sensor 10 PSI (68.95 kPa) Absolute Male - 1/4" (6.35mm) NPT 4 mA ~ 20 mA Probe 制造商:cynergy 3 系列:IPSLU 零件状态:有效 压力类型:绝对 工作压力:10 PSI（68.95 kPa） 输出类型:模拟电流 输出:4 mA ~ 20 mA 精度:±0.5% 电压 - 电源:9 V ~ 32 V 端口尺寸:公型 - 1/4"（6.35mm） NPT 端口样式:有螺纹 特性:放大输出，温度补偿 端子类型:连接器 最高压力:- 工作温度:-20°C ~ 80°C 封装/外壳:探头组件 供应商器件封装:探头组件 标准包装:1 |
| IPSLU-AP015-5 | 功能描述:Pressure Sensor 15 PSI (103.42 kPa) Absolute Male - 1/4" (6.35mm) NPT 4 mA ~ 20 mA Probe 制造商:cynergy 3 系列:IPSLU 零件状态:有效 压力类型:绝对 工作压力:15 PSI（103.42 kPa） 输出类型:模拟电流 输出:4 mA ~ 20 mA 精度:±0.5% 电压 - 电源:9 V ~ 32 V 端口尺寸:公型 - 1/4"（6.35mm） NPT 端口样式:有螺纹 特性:放大输出，温度补偿 端子类型:连接器 最高压力:- 工作温度:-20°C ~ 80°C 封装/外壳:探头组件 供应商器件封装:探头组件 标准包装:1 |
| IPSLUAT-AP005-5 | 功能描述:Pressure Sensor 5 PSI (34.47 kPa) Absolute Male - 1/4" (6.35mm) NPT 4 mA ~ 20 mA Cylinder, Threaded 制造商:cynergy 3 系列:IPSLU 零件状态:有效 压力类型:绝对 工作压力:5 PSI（34.47 kPa） 输出类型:模拟电流 输出:4 mA ~ 20 mA 精度:±0.5% 电压 - 电源:9 V ~ 32 V 端口尺寸:公型 - 1/4"（6.35mm） NPT 端口样式:有螺纹 特性:放大输出，温度补偿 端子类型:连接器 最高压力:75 PSI（517.11 kPa） 工作温度:-20°C ~ 80°C 封装/外壳:圆柱形，有螺纹 供应商器件封装:* 标准包装:1 |
| IPSLUAT-AP010-5 | 功能描述:Pressure Sensor 10 PSI (68.95 kPa) Absolute Male - 1/4" (6.35mm) NPT 4 mA ~ 20 mA Cylinder, Threaded 制造商:cynergy 3 系列:IPSLU 零件状态:有效 压力类型:绝对 工作压力:10 PSI（68.95 kPa） 输出类型:模拟电流 输出:4 mA ~ 20 mA 精度:±0.5% 电压 - 电源:9 V ~ 32 V 端口尺寸:公型 - 1/4"（6.35mm） NPT 端口样式:有螺纹 特性:放大输出，温度补偿 端子类型:连接器 最高压力:75 PSI（517.11 kPa） 工作温度:-20°C ~ 80°C 封装/外壳:圆柱形，有螺纹 供应商器件封装:* 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。