参数资料
型号: IR3500VMTRPBF
厂商: International Rectifier
文件页数: 7/34页
文件大小: 0K
描述: IC XPHASE3 CTLR VR11.1 32-MLPQ
标准包装: 1
系列: XPhase3™
应用: 处理器
电流 - 电源: 6.5mA
电源电压: 4.75 V ~ 7.5 V
工作温度: 0°C ~ 100°C
安装类型: 表面贴装
封装/外壳: 32-VFQFN 裸露焊盘
供应商设备封装: 32-MLPQ(5x5)
包装: 标准包装
其它名称: IR3500VMTRPBFDKR
IR3500V
PIN DESCRIPTION
PIN#
1-8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
PIN SYMBOL
VID7-0
ENABLE
VRHOT
HOTSET
VOSEN-
VOSEN+
VO
FB
EAOUT
VDRP
IIN
VSETPT
OCSET
VDAC
SS/DEL
ROSC/OVP
LGND
CLKOUT
PHSOUT
PHSIN
VCCL
VCCLFB
PIN DESCRIPTION
VID0, 1, 5, 7 are grounded. VID6 is pulled up. VID2~4 are inputs to VID D to A
converter.
Enable input. A logic low applied to this pin puts the IC into fault mode. Do not float
this pin as the logic state will be undefined.
Open collector output of the VRHOT comparator which drives low if HOTSET pin
voltage is lower than 1.6V. Connect external pull-up.
A resistor divider including thermistor senses the temperature, which is used for
VRHOT comparator.
Remote sense amplifier input. Connect to ground at the load.
Remote sense amplifier input. Connect to output at the load.
Remote sense amplifier output.
Inverting input to the error amplifier.
Output of the error amplifier.
Buffered IIN signal. Connect an external RC network to FB to program converter
output impedance.
Average current input from the phase IC(s). This pin is also used to communicate
over voltage condition to phase ICs.
Error amplifier non-inverting input. Converter output voltage can be decreased from
the VDAC voltage with an external resistor connected between VDAC and this pin
(there is an internal sink current at this pin).
Programs the constant converter output current limit and hiccup over-current
thresholds through an external resistor tied to VDAC and an internal current source
from this pin. Over-current protection can be disabled by connecting a resistor from
this pin to VDAC to program the threshold higher than the possible signal into the IIN
pin from the phase ICs but no greater than VCCL – 2V (do not float this pin as
improper operation will occur).
Regulated voltage programmed by the VID inputs. Connect an external RC network
to LGND to program dynamic VID slew rate and provide compensation for the
internal buffer amplifier.
Programs converter startup and over current protection delay timing. It is also used
to compensate the constant output current loop during soft start. Connect an
external capacitor to LGND to program.
Connect a resistor to LGND to program oscillator frequency and OCSET, VSETPT
and VDAC bias currents. Oscillator frequency equals switching frequency per phase.
The pin voltage is 0.6V during normal operation and higher than 1.6V if over-voltage
condition is detected.
Local Ground for internal circuitry and IC substrate connection.
Clock output at switching frequency multiplied by phase number. Connect to CLKIN
pins of phase ICs.
Phase clock output at switching frequency per phase. Connect to PHSIN pin of the
first phase IC.
Feedback input of phase clock. Connect to PHSOUT pin of the last phase IC.
Output of the voltage regulator, and power input for clock oscillator circuitry. Connect
a decoupling capacitor to LGND.
Non-inverting input of the voltage regulator error amplifier. Output voltage of the
regulator is programmed by the resistor divider connected to VCCL.
Page 7 of 34
July 28, 2008
相关PDF资料
PDF描述
IR3502AMTRPBF IC XPHASE CTRL VR11.0/1 32-MLPQ
IR3502BMTRPBF IC REG XPH INTEL VR11.1 32-MLPQ
IR3502MTRPBF IC XPHASE3 CONTROLLER 32-MLPQ
IR3503MTRPBF IC CTRL XPHASE VR11.0/1 32-MLPQ
IR3504MTRPBF IC CTRL XPHASE3 SVID 32-MLPQ
相关代理商/技术参数
参数描述
IR3502 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM CONTROL IC
IR3502_09 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM CONTROL IC
IR3502A 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM CONTROL IC
IR3502AMPBF 制造商:IRF 制造商全称:International Rectifier 功能描述:XPHASE3TM CONTROL IC
IR3502AMTRPBF 功能描述:IC XPHASE CTRL VR11.0/1 32-MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 电源管理 - 专用 系列:XPhase3™ 应用说明:Ultrasound Imaging Systems Application Note 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:37 系列:- 应用:医疗用超声波成像,声纳 电流 - 电源:- 电源电压:2.37 V ~ 6 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:56-WFQFN 裸露焊盘 供应商设备封装:56-TQFN-EP(8x8) 包装:管件