参数资料
| 型号： | ISL6322IRZ |
| 厂商： | Intersil |
| 文件页数： | 28/41页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR PWM 4PHASE BUCK 48-QFN |
| 标准包装： | 43 |
| 应用： | 控制器，Intel VR10、VR11、AMD CPU |
| 输入电压： | 5 V ~ 12 V |
| 输出数： | 1 |
| 输出电压： | 0.38 V ~ 1.99 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘 |
| 供应商设备封装： | 48-QFN（7x7） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页
ISL6322
Acknowledge
Each address and data transmission uses 9 clock pulses.
The ninth pulse is the acknowledge bit (A). After the start
condition, the master sends 7 slave address bits and a R/W
bit during the next 8 clock pulses. During the ninth clock
pulse, the device that recognizes its own address holds the
data line low to acknowledge. The acknowledge bit is also
used by both the master and the slave to acknowledge
receipt of register addresses and data as described below.
SCL
Adaptive Deadtime Control, Overvoltage Protection, and
Switching Frequency parameters. Once the ISL6322
receives a correct register address byte, it responds with an
acknowledge.
Writing to the Internal Registers
In order to change any of the four operating parameters via
the I2C bus, the internal registers must be written to. The
two registers inside the ISL6322 can be written individually
with two separate write transactions or sequentially with one
write transaction by sending two data bytes as described
below.
1
2
8
9
To write to a single register in the ISL6322, the master sends
SDA
MSB
a control byte with the R/W bit set to 0, indicating a write. If it
receives an Acknowledge from the ISL6322, it sends a
register address byte representing the internal register it
START
ACKNOWLEDGE
FROM SLAVE
FIGURE 18. ACKNOWLEDGE ON THE I 2 C BUS
wants to write to (0000_0000 for RGS1 or 0000_0001 for
RGS2). The ISL6322 will respond with an Acknowledge. The
master then sends a byte representing the data byte to be
written into the desired register. The ISL6322 will respond
ISL6322 I 2 C Slave Address
All devices on the I 2 C bus must have a 7-bit I 2 C address in
order to be recognized. The ISL6322 has two user
selectable addresses to ensure it does not interfere with
other devices on the bus. The address is programmed via
the R ss resistor on the SS/RST/A0 pin. Placing the R ss
resistor from the SS/RST/A0 pin to ground sets the I 2 C
address to be 1000_110. If the R ss resistor is placed from
the SS/RST/A0 pin to VCC the address is 1000_111.
Please note that the I 2 C address of the ISL6322 is
programmed from the SS/RST/A0 pin as soon as VCC rises
above the POR threshold. The ISL6322’s I 2 C address stays
the same and can not be reprogrammed until VCC falls back
below the POR falling threshold.
Communicating Over the I 2 C Bus
Two transactions are supported on the I 2 C interface: 1) Write
register, 2) Read register from current address.
All transactions start with a control byte sent from the I 2 C
master device. The control byte begins with a Start condition,
followed by 7-bits of slave address. The last bit sent by the
master is the R/W bit and is 0 for a write or 1 for a read. If any
slaves on the I 2 C bus recognize their address, they will
Acknowledge by pulling the serial data line low for the last clock
cycle in the control byte. If no slaves exist at that address or are
not ready to communicate, the data line will be 1, indicating a
Not Acknowledge condition.
Once the control byte is sent, and the ISL6322
acknowledges it, the 2nd byte sent by the master must be a
register address byte. This register address byte tells the
ISL6322 which one of the two internal registers it wants to
write to or read from. The address of the first internal
register, RGS1, is 0000_0000. This register sets the Voltage
Margining Offset. The address of the second internal
register, RGS2, is 0000_0001. This register sets the
28
with an Acknowledge. The master then issues a Stop
condition, indicating to the ISL6322 that the current
transaction is complete. Once this transaction completes,
the ISL6322 will immediately update and change the
operating parameters on-the-fly.
It is also possible to write to both registers sequentially. To
do this the master must write to register RGS1 first. This
transaction begins with the master sending a control byte
with the R/W bit set to 0. If it receives an Acknowledge from
the ISL6322, it sends the register address byte 0000_0000,
representing the internal register RGS1. The ISL6322 will
respond with an Acknowledge. After sending the data byte to
RGS1 and receiving an Acknowledge from the ISL6322,
instead of sending a Stop condition, the master sends the
data byte to be stored in register RGS2. The ISL6322 will
respond with an Acknowledge. The master then issues a
Stop condition, indicating to the ISL6322 that the current
transaction is complete. Once this transaction completes the
ISL6322 will immediately update and change the operating
parameters on-the-fly.
FN6328.2
August 2, 2007
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6323AIRZ | IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323BIRZ | IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323IRZ | IC HYBRID CTRLR PWM MONO 48-QFN |
| ISL6324AIRZ | IC HYBRID CTRLR PWM DUAL 48QFN |
| ISL6324IRZ | IC HYBRID CTRLR PWM DUAL 48-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ISL6322IRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| ISL6323ACRZ | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323ACRZR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONT. FOR CORE+NORTHBRIDGE,1 PHASE PSI, 3.4MHZ SVI - Rail/Tube 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
| ISL6323ACRZ-T | 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| ISL6323ACRZ-TR5381 | 制造商:Intersil Corporation 功能描述:4+1 PHASE CONTROLLER, CORE+NORTHBRIDGE,1 PHASE PSI,3.4MHZ SV - Tape and Reel 制造商:Intersil Corporation 功能描述:IC PWM CTRLR SYNC BUCK DL 48QFN |
发布紧急采购，3分钟左右您将得到回复。