- 您现在的位置：买卖IC网 > PDF目录1833 > LTC3876EFE#PBF (Linear Technology)IC CTLR DC/DC DDR DUAL 38-TSSOP PDF资料下载
参数资料
| 型号： | LTC3876EFE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 28/48页 |
| 文件大小： | 0K |
| 描述： | IC CTLR DC/DC DDR DUAL 38-TSSOP |
| 产品培训模块： | LTC3876 Dual DC/DC Controller |
| 标准包装： | 50 |
| 应用： | 控制器，DDR，DDR2，DDR3 |
| 输入电压： | 4.5 V ~ 38 V |
| 输出数： | 2 |
| 输出电压： | 可调 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-TFSOP （0.173"，4.40mm 宽）裸露焊盘 |
| 供应商设备封装： | 38-TSSOP 裸露焊盘 |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
LTC3876
APPLICATIONS INFORMATION
can be used to set a V IN to turn on a channel’s switching.
If resistor dividers are used on both RUN pins, when V IN
is low enough and both RUN pins are pulled below the
~0.8V threshold, the part will shut down all bias of INTV CC
this phase to ensure smooth soft-start or tracking. The
soft-start or tracking range is defined to be the voltage
range from 0V to 0.6V on the TRACK/SS pin. The total
soft-start time can be calculated as:
and DRV CC and be put in micropower shutdown mode.
The RUN pins’ bias currents depend on the RUN voltages.
The bias current changes should be taken into account
t SS (SEC) = 0.6(V) ?
C SS (μF)
1(μA)
when designing the external voltage divider UVLO circuit.
An internal proportional-to-absolute-temperature (PTAT)
pull-up current source (~2.5μA at 25°C) is constantly con-
nected to this pin. When a RUN pin rises above 1.2V, the
corresponding channel’s TG and BG drives are turned on
and an additional 4μA temperature-independent pull-up
current is connected internally to the RUN pin. Pulling the
RUN pin to fall below 1.2V by more than an 80mV hyster-
esis turns off TG and BG of the corresponding channel,
and the additional 10μA pull-up current is disconnected.
As voltage on a RUN pin increases, typically beyond 3V,
its bias current will start to reverse direction and flow into
the RUN pin. Keep in mind that neither of the RUN pins
can sink more than 50μA; Even if a RUN pin may slightly
exceed 6V when sinking 50μA, a RUN pin should never
be forced to higher than 6V by a low impedance voltage
source to prevent faulty conditions.
Soft-Start and Tracking
The LTC3876 has the ability to either soft-start by itself
with a capacitor or track the output of another channel
or an external supply. Note that the soft-start or tracking
features are achieved not by limiting the maximum output
current of the controller, but by controlling the output ramp
voltage according to the ramp rate on the TRACK/SS pin.
When channel 1 is configured to soft-start by itself, a capaci-
tor should be connected to its TRACK/SS pin. TRACK/SS
is pulled low until the RUN pin voltage exceeds 1.2V and
UVLO is released, at which point an internal current of
When one particular channel is configured to track an
external supply, a voltage divider can be used from the
external supply to the TRACK/SS pin to scale the ramp
rate appropriately. Two common implementations are co-
incidental tracking and ratiometric tracking. For coincident
tracking, make the divider ratio from the external supply
the same as the divider ratio for the differential feedback
voltage. Ratiometric tracking could be achieved by using
a different ratio than the differential feedback.
Note that the 1μA soft-start capacitor charging current is
still flowing, producing a small offset error. To minimize
this error, select the tracking resistive divider values to be
small enough to make this offset error negligible.
The LTC3876 allows the user to program how channel 1
VDDQ tracks an external power supply. Channel 2 VTT will
always track VDDQ and be equal to 0.5 ? VDDQ.
By selecting different resistors, the LTC3876 can achieve
different modes of tracking including the two in Figure 8a.
To implement the coincident tracking, connect an additional
resistive divider to the external power supply and connect
its midpoint to the TRACK/SS pin of the slave channel.
The ratio of this divider should be the same as that of the
slave channel’s feedback divider shown in Figure 8b. In
this tracking mode, the external power supply must be set
higher than VDDQ. To implement the ratiometric tracking,
the master channel’s feedback divider can be also used
to provide TRACK/SS voltage for the slave channel, since
the additional divider, if used, should be of the same ratio
as the master channel’s feedback divider.
1μA charges the soft-start capacitor, C SS , connected to the
TRACK/SS pin. Current-limit foldback is disabled during
3876f
28
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3878EGN#PBF | IC REG CTRLR BUCK PWM CM 16-SSOP |
| LTC3879EUD#PBF | IC REG CTRLR BUCK PWM CM 16-QFN |
| LTC3880EUJ-1#PBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LTC3890EUH#PBF | IC REG CTRLR BUCK PWM CM 32-QFN |
| LTC3891EFE#PBF | IC REG CTRLR BUCK PWM CM 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3876EUHF#PBF | 功能描述:IC CTLR DC/DC DDR DUAL 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3876EUHF#TRPBF | 功能描述:IC CTLR DC/DC DDR DUAL 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3876IFE#PBF | 功能描述:IC CTLR DC/DC DDR DUAL 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3876IFE#TRPBF | 功能描述:IC CTLR DC/DC DDR DUAL 38-TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
| LTC3876IUHF#PBF | 功能描述:IC CTLR DC/DC DDR DUAL 38-QFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:43 系列:- 应用:控制器，Intel VR11 输入电压:5 V ~ 12 V 输出数:1 输出电压:0.5 V ~ 1.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商设备封装:48-QFN（7x7） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。