- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4099EUDC#PBF (Linear Technology)IC USB PWR MANAGER/CHRGR 20-QFN PDF资料下载
参数资料
| 型号： | LTC4099EUDC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 17/36页 |
| 文件大小： | 0K |
| 描述： | IC USB PWR MANAGER/CHRGR 20-QFN |
| 标准包装： | 91 |
| 系列： | PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4099
OPERATION
2000
1200
400
I CHG = PROG ? 1030
R PROG
I BAT = PROG ? 1030
If the load current increases beyond the power allowed
from the switching regulator, additional power will be pulled
from the battery via the ideal diodes. Furthermore, if power
to V BUS (USB or wall adapter) is removed, then all of the
application power will be provided by the battery via the
ideal diodes. The ideal diodes will be fast enough to keep
V OUT from drooping with only the storage capacitance
required for the switching regulator. The internal ideal
diode consists of a precision amplifier that activates a
large on-chip MOSFET transistor whenever the voltage at
V OUT is approximately 15mV (V FWD ) below the voltage at
BAT. Within the amplifier’s linear range, the small-signal
resistance of the ideal diode will be quite low, keeping
the forward drop near 15mV. At higher current levels, the
MOSFET will be in full conduction.
2200
VISHAY Si2333
EXTERNAL
1800 IDEAL DIODE
1600
1400
LTC4099
IDEAL DIODE
1000
800
600 ON
SEMICONDUCTOR
MBRM120LT3
200
0
0 60 120 180 240 300 360 420 480
FORWARD VOLTAGE (mV) (BAT – V OUT ) 4099 F03
Figure 3. Ideal Diode V-I Characteristics
To supplement the internal ideal diode, an external
P-channel MOSFET transistor may be added from BAT to
V OUT . The IDGATE pin of the LTC4099 drives the gate of
the external P-channel MOSFET transistor for automatic
ideal diode control. The source of the external P-channel
MOSFET should be connected to V OUT and the drain should
be connected to BAT. Capable of driving a 1nF load, the
IDGATE pin can control an external P-channel MOSFET
transistor having an on-resistance of 30mΩ or lower.
Battery Charger
The LTC4099 includes a battery charger with low voltage
precharge, constant-current/constant-voltage charging, C/x
state-of-charge detection, automatic termination by safety
timer, automatic recharge, bad cell detection and thermistor
sensor input for out-of-temperature charge pausing.
Precharge
When a battery charge cycle begins, the battery charger
first determines if the battery is deeply discharged. If the
battery voltage is below V TRKL , typically 2.85V, an automatic
trickle charge feature sets the battery charge current to
one-fifth of the default charge current. If the low voltage
persists for more than one-half hour, the battery charger
automatically terminates and indicates via the I 2 C port
that the battery was unresponsive.
Constant-Current
Once the battery voltage is above V TRKL , the charger begins
charging in full power constant-current mode. The current
delivered to the battery will try to reach V PROG /R PROG ?
1030 where V PROG can be set by the I 2 C port and ranges
from 500mV to 1.2V in 100mV steps. The default value
of V PROG is 500mV. Depending on available input power
and external load conditions, the battery charger may or
may not be able to charge at the full programmed rate.
The external load will always be prioritized over the battery
charge current. Likewise, the USB current limit program-
ming will always be observed and only additional power
will be available to charge the battery. When system loads
are light, battery charge current will be maximized.
As mentioned above, the upper limit of charge current is
programmed by the combination of a resistor from PROG
to ground and the PROG servo voltage value set in the
I 2 C port. The charge current will be given by the following
expression:
V
Eight values of V PROG may be selected by the I CHARGE2 ,
I CHARGE1 and I CHARGE0 bits in the I 2 C port. See Table 3.
In either the constant-current or constant-voltage charging
modes, the voltage at the PROG pin will be proportional to
the actual charge current delivered to the battery. The charge
current can be determined at any time by monitoring the
PROG pin voltage and using the following relationship:
V
R PROG
4099fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4100EG#TR | IC CHARGER SMART BATTERY 24-SSOP |
| LTC4101EG#PBF | IC CNTRLR BATT CHRG 24-SSOP |
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4100 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Smart Battery System Manager Available in 48-Lead TSSOP Package |
| LTC4100_09 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4100EG | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4100EG#PBF | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4100EG#TR | 功能描述:IC CHARGER SMART BATTERY 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。