- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4099EUDC#PBF (Linear Technology)IC USB PWR MANAGER/CHRGR 20-QFN PDF资料下载
参数资料
| 型号： | LTC4099EUDC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 24/36页 |
| 文件大小： | 0K |
| 描述： | IC USB PWR MANAGER/CHRGR 20-QFN |
| 标准包装： | 91 |
| 系列： | PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4099
OPERATION
Table 5 lists the possible safety timer settings from 1 to 8
hours, and how to decode them. The default state for the
LTC4099 safety timer is 4 hours.
Table 5. Safety Timer Decode
prohibits the generation of an interrupt. The start-up state
of the LTC4099 is all zeros for this register indicating that
no interrupts will be generated without explicit request via
the I 2 C port. See the Interrupt Generation section.
TIMER2
0
0
0
0
1
1
1
1
SAFETY T IMER SETTINGS
TIMER1 TIMER0
0 0
0 1
1 0
1 1
0 0
0 1
1 0
1 1
TIMEOUT
4 Hours*
5 Hours
6 Hours
7 Hours
8 Hours
1 Hour
2 Hours
3 Hours
Output Data
One status byte may be read from the LTC4099. Table 6
represents the status byte information. A 1 read back in
any of the bit positions indicates that the condition is true.
For example, 1s read back from bits 7 and 2 indicate that
power is available at V BUS , and that the battery charger’s
thermistor has halted charging due to an undertemperature
condition at the battery.
*Default Setting
The DISABLE_CHARGER bit can be used to prevent battery
charging if needed. This bit should be used with caution
as it can prevent the battery charger from bringing up
the battery voltage. Without the ability to address the I 2 C
port, only a low voltage on DV CC will clear the I 2 C port to
its default state and re-enable charging.
Table 6. LTC4099 Status Data Bytes
READ BYTE
Bit 7 (MSB)
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
STATUS REGISTER
USBGOOD
WALLGOOD
BADCELL
THERMAL REG
NTC1 See Table 7
NTC0
The ENABLE_BATTERY_CONDITIONER bit enables the
automatic battery load circuit in the event of simultaneously
high battery voltage and temperature. See the Overtem-
perature Battery Conditioner section.
The V FLOAT = 4.2V bit controls the final float voltage of the
LTC4099’s battery charger. A 1 in this bit position changes
the charger from the default float voltage value of 4.100V
to the higher 4.200V level.
The T REG = 85°C control bit changes the LTC4099’s battery
charger junction thermal regulation temperature from its
default value of 105°C to a lower setting of 85°C. This may
be used to reduce heat in highly thermally compromised
systems. In general, the high efficiency charging system
of the LTC4099 will keep the junction temperature low
enough to avoid junction thermal regulation.
The third and final byte of input data at sub address 0x02
is the mask register. The mask register determines which
status change events or categories will be allowed to gener-
ate an interrupt. A 1 written to a given position in the mask
register allows status change in that category to generate
an interrupt. A zero in a given position in the mask register
Bit 1 CHRGR1 See Table 8
Bit 0 (LSB) CHRGR0
Bit 7 in the status byte indicates the presence of power
at V BUS . Criteria for determining this status bit is derived
from the undervoltage lockout circuit on V BUS and is given
by the electrical parameters V UVLO and V DUVLO .
Bit 6 indicates the presence of voltage available at the WALL
pin and is derived from the WALL undervoltage lockout
circuit. Like the V BUS pin, this pin has both an absolute
voltage detection level given by the electrical parameter
V WALL , as well as a level relative to BAT given by Δ V WALL .
Both of the conditions must be met for bit 6 to indicate
the presence of power at WALL.
Bit 5 indicates that the battery has been below the pre-
charge threshold level of approximately 2.85V for more
than one-half hour while the charger was attempting to
charge. When this occurs, it is usually the result of a de-
fective cell. However, in some cases a bad cell indication
may be caused by system load prioritization over battery
charging. System software can test for this by forcing a
reduction of system load and restarting the battery charger
4099fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4100EG#TR | IC CHARGER SMART BATTERY 24-SSOP |
| LTC4101EG#PBF | IC CNTRLR BATT CHRG 24-SSOP |
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4100 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Smart Battery System Manager Available in 48-Lead TSSOP Package |
| LTC4100_09 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4100EG | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4100EG#PBF | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4100EG#TR | 功能描述:IC CHARGER SMART BATTERY 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。