- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4099EUDC#PBF (Linear Technology)IC USB PWR MANAGER/CHRGR 20-QFN PDF资料下载
参数资料
| 型号： | LTC4099EUDC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 18/36页 |
| 文件大小： | 0K |
| 描述： | IC USB PWR MANAGER/CHRGR 20-QFN |
| 标准包装： | 91 |
| 系列： | PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4099
OPERATION
Recall, however, that in many cases the actual battery
charge current, I BAT , will be lower than the programmed
current, I CHG , due to limited input power available and
prioritization of the system load drawn from V OUT .
Constant-Voltage
Once the battery terminal voltage reaches the preset float
voltage, the battery charger will hold the voltage steady
and the charge current will decrease naturally toward
zero. Two voltage settings, 4.100V and 4.200V, are avail-
able for final float voltage selection via the I 2 C port. For
applications that require as much run time as possible,
the 4.200V setting can be selected. For applications that
seek to extend battery life, the LTC4099’s default setting
of 4.100V should be used.
Full Capacity Charge Indication (C/x)
Since the PROG pin always represents the actual charge
current flowing, even in the constant-voltage phase of
charging, the PROG pin voltage represents the battery’s
state-of-charge during that phase. The LTC4099 has a full
capacity charge indication comparator on the PROG pin
which reports its results via the I 2 C port. Selection levels
for the C/x comparator of 50mV, 100mV, 200mV and 500mV
are available by I 2 C control. Recall that the PROG pin servo
voltage can be programmed from 500mV to 1.2V. If the 1V
servo setting represents the full charge rate of the battery
(1C), then the 100mV C/x setting would be equivalent to
C/10. Likewise the 200mV C/x setting would represent
C/5 and the 500mV setting C/2.
Charge Termination
The battery charger has a built-in termination safety
timer. When the voltage on the battery reaches the user-
programmed float voltage of 4.100V or 4.200V, the safety
timer is started. After the safety timer expires, charging of
the battery will discontinue and no more current will be
delivered. The safety timer’s default ending time of four
hours may be altered from one to eight hours in one-hour
increments by accessing the I 2 C port.
Automatic Recharge
After the battery charger terminates, it will remain off,
drawing only microamperes of current from the battery.
If the portable product remains in this state long enough,
the battery will eventually self discharge. To ensure that
the battery is always topped off, a new charge cycle will
automatically begin when the battery voltage falls below
V RECHRG (typically 4.100V for the 4.200V float voltage
setting and 4.000V for the 4.100V float voltage setting). In
the event that the safety timer is running when the battery
voltage falls below V RECHRG , it will reset back to zero. To
prevent brief excursions below V RECHRG from resetting the
safety timer, the battery voltage must be below V RECHRG for
more than 2.5ms. The charge cycle and safety timer will
also restart if the V BUS UVLO cycles LOW and then HIGH
(e.g., V BUS or WALL is removed and then replaced) or if
the charger is momentarily disabled using the I 2 C port.
The flow chart in Figure 4 represents the battery charger’s
algorithm.
Thermistor Measurement
The battery temperature is measured by placing a nega-
tive temperature coefficient (NTC) thermistor close to
the battery pack. The thermistor circuitry is shown in the
Block Diagram.
To use this feature, connect the thermistor between the NTC
pin and ground and a bias resistor from NTCBIAS to NTC.
The bias resistor should be a 1% resistor with a value equal
to the value of the chosen thermistor at 25°C (R25).
The LTC4099 will pause charging when the resistance of
the thermistor drops to 0.484 times the value of R25 or
4.84k for a 10k thermistor. For a Vishay curve 2 thermis-
tor, this corresponds to approximately 45°C. If the battery
charger is in constant-voltage (float) mode, the safety
timer also pauses until the thermistor indicates a return
to valid temperature. The LTC4099 is also designed to
pause charging when the value of the thermistor increases
to 2.816 times the value of R25. For a Vishay curve 2
10k thermistor, this resistance, 28.16k, corresponds to
approximately 0°C. The hot and cold comparators each
have approximately 4°C of hysteresis to prevent oscillation
about the trip point.
If the curve 2 thermistor’s temperature rises above 60°C,
its value will drop to 0.2954 times R25. When this happens,
the LTC4099 detects this critically high temperature and
indicates it via the I 2 C port (see Table 7). If this condition
4099fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4100EG#TR | IC CHARGER SMART BATTERY 24-SSOP |
| LTC4101EG#PBF | IC CNTRLR BATT CHRG 24-SSOP |
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4100 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Smart Battery System Manager Available in 48-Lead TSSOP Package |
| LTC4100_09 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4100EG | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4100EG#PBF | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4100EG#TR | 功能描述:IC CHARGER SMART BATTERY 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。