- 您现在的位置：买卖IC网 > PDF目录1834 > LTC4099EUDC#PBF (Linear Technology)IC USB PWR MANAGER/CHRGR 20-QFN PDF资料下载
参数资料
| 型号： | LTC4099EUDC#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 25/36页 |
| 文件大小： | 0K |
| 描述： | IC USB PWR MANAGER/CHRGR 20-QFN |
| 标准包装： | 91 |
| 系列： | PowerPath™ |
| 功能： | 电源管理 |
| 电池化学： | 锂离子（Li-Ion）、锂聚合物（Li-Pol） |
| 电源电压： | 4.35 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 供应商设备封装： | 20-QFN（3x4） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
LTC4099
OPERATION
via I 2 C (a disable followed by an enable). If the bad cell
indication returns, then the cell is definitively bad.
Bit 4 indicates that the battery charger is in thermal regula-
tion due to excessive LTC4099 junction temperature. Recall
that there are two I 2 C programmable junction temperature
settings available at which to regulate, 85°C and 105°C.
Bit 4 indicates thermal regulation at whichever setting is
chosen.
Bits 3 and 2 indicate the status of the thermistor measure-
ment circuit and are decoded in Table 7. The BATTERY
TOO COLD and BATTERY TOO HOT states indicate that
the thermistor temperature is out of range (either below
0°C or above 45°C for a curve 2 thermistor) and that
charging has paused until a return to valid temperature.
The BATTERY OVERTEMPERATURE state indicates that
the battery’s thermistor has reached a critical temperature
(above 60°C for a curve 2 thermistor) and that long term
battery capacity may be seriously compromised if the
condition persists.
Table 7. NTC1, NTC0 Decode
THERMISTOR STATUS BIT DECODE
NTC1 NTC0 THERMISTOR STATUS
0 0 NO NTC FAULT
0 1 BATTERY TOO COLD
1 0 BATTERY TOO HOT
1 1 BATTERY OVERTEMPERATURE
Table 8. CHRGR1, CHRGR0 Decode
BATTERY CHARGER STATUS BIT DECODE
CHRGR1 CHRGR0 CHARGER STATUS
0 0 CHARGER OFF
0 1 CONSTANT-CURRENT
1 0 CONSTANT V, I BAT > C/x
1 1 CONSTANT V, I BAT < C/x
Bits 1 and 0 indicate the status of the battery charger, and
are decoded into one of four possible battery charger states
in Table 8. The constant-current state indicates that the
battery charger is attempting to charge with all available
current up to the constant-current level programmed,
and that the battery has not yet reached the float voltage.
The CONSTANT V, I BAT > C/x bit indicates that the battery
charger has entered the float voltage phase of charging
(BAT at 4.1V or 4.2V), but that the charge current is still
above the C/x detection level programmed. The CONSTANT
V, I BAT <C/x bit indicates that the battery charge current
has dropped below the C/x detection level programmed,
and that charging is virtually complete. Note that if the
current limited USB compliant switching regulator is in
input current regulation, then the actual battery charge
current may be less than C/x due to insufficient available
power. If the LTC4099 is in input current limit, the charge
status bits will lock out (disallow) the state 1-1, indicating
that charging is complete. This feature prevents false full
capacity charge indications due to insufficient power to
the battery charger.
The status read from the LTC4099 is captured in one of
two ways. If an interrupt is currently pending, then the
available data represents the state of the LTC4099 at the
time the interrupt was generated. If no interrupt is pending,
then the data is captured when the LTC4099 acknowledges
its read address. In the case of a pending interrupt, fresh
data can be assured by taking two consecutive readings
of the status information and discarding the first set.
Shutdown Mode
The USB switching regulator is enabled whenever V BUS
is above V UVLO , greater than V DUVLO above BAT and the
LTC4099 is not in one of the two USB suspend modes
(500μA or 2.5mA). When power is available from both
the USB (V BUS ) and WALL inputs, the auxiliary (WALL)
input is prioritized and the USB switching regulator is
disabled.
The battery charger will always start a charge cycle when
power is detected at V BUS or WALL. It can only be shut
down via a command from the I 2 C port or by normal
termination after a charge cycle.
The ideal diode is enabled at all times and cannot be
disabled.
4099fd
相关PDF资料 |
PDF描述 |
|---|---|
| LTC4100EG#TR | IC CHARGER SMART BATTERY 24-SSOP |
| LTC4101EG#PBF | IC CNTRLR BATT CHRG 24-SSOP |
| LTC4110EUHF#TRPBF | IC BATTERY BACKUP MANAGER 38-QFN |
| LTC4150IMS#TRPBF | IC COUNTER/GAUGE GAS/BATT 10MSOP |
| LTC4155IUFD#TRPBF | IC I2C POWER MANAGER DUAL 28QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4100 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Smart Battery System Manager Available in 48-Lead TSSOP Package |
| LTC4100_09 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Smart Battery Charger Controller |
| LTC4100EG | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| LTC4100EG#PBF | 功能描述:IC SMART BATTERY CHARGER 24-SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 其它有关文件:STC3100 View All Specifications 特色产品:STC3100 - Battery Monitor IC 标准包装:4,000 系列:- 功能:燃料，电量检测计/监控器 电池化学:锂离子（Li-Ion） 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MiniSO 包装:带卷 (TR) 其它名称:497-10526-2 |
| LTC4100EG#TR | 功能描述:IC CHARGER SMART BATTERY 24-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。