- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
and ranges. It should be noted that even if the LTC4110
TYPE pin is not set to a smart battery mode, any SMBus
commands sent by a host or a smart battery are still
acted upon. For SuperCap support, see the Applications
Information section.
BATTERY BACKUP MODE
Figure 1 shows the LTC4110 in backup mode and the
corresponding PowerPath enabled. The LTC4110 use the
DCDIV pin to typically monitor the DCIN voltage through
an external resistor divider. The DCDIV pin sets the backup
mode threshold voltage and senses the need to enter
backup mode. DCDIV can alternately be driven with other
signals such as logic. When the DCDIV pin voltage drops
below the AC present threshold voltage (see V AC ) backup
mode is entered. Backup mode is also entered whenever
the internal undervoltage lockout, UVLO, senses that DCIN
(V UVD ) or DCOUT has fallen to excessively low voltages.
In backup mode the battery P-MOSFET ideal diode is
enabled to backup the load from the battery. The supply
input P-MOSFET ideal diode isolates the main supply
input from the load and the ?yback switcher N-MOSFETs
are inhibited from turning on. Also, after the threshold is
passed, hysteresis (V ACH ) is switched in. When the supply
is returning and the AC present threshold voltage plus the
hysteresis voltage is reached on the DCDIV pin, both of the
battery P-MOSFETs are rapidly switched off (t dDOFF ) and
the supply input P-MOSFET ideal diode provides the load
current. When forward biased, the ideal diodes regulate
their forward voltage drop to 20mV typical (V FR ) when the
MOSFET is suf?ciently sized. If the voltage input falls and
results in a forward voltage below 20mV, then the ideal
diode will begin turning off at a slow rate. Should the ideal
diode see a –18mV typical (V REV ) or lower reverse voltage,
the ideal diode will turn off quickly (t dDOFF ).
While in backup, the battery’s average cell voltage is moni-
tored to protect the battery from excessive discharge. If
the cell voltage drops below the value programmed by the
V DIS pin (Li-Ion default = 2.75V/cell, NiMH/NiCd default
= 0.95V/cell, lead acid default = 1.93V/cell), the battery
P-MOSFETs are rapidly turned off and the battery is dis-
connected from the load. If DCIN is above UVLO, the load
and the LTC4110 will be powered from the supply input. If
DCIN is below UVLO, the LTC4110 enters the micropower
shutdown mode (see the Shutdown Mode section for more
details). Also, the SMBus accessible BKUP_FLT fault bit
is set and maintained as long as suf?cient battery voltage
is present (V BAT ≥ 2.7V). This fault bit can be read after
DCIN returns to a voltage level exceeding the internal
UVLO threshold (see V UVI ) and DCOUT has regained suf-
?cient voltage (see DCOUT) to provide internal power. If
the GPIO2 port is programmed as the BKUP_FLTb status
output after DCIN returns, it will be forced low to repre-
sent an inverted BKUP_FLT bit. When DCIN returns, as
sensed by the UVLO, the shutdown mode is automatically
cancelled and normal operation can resume, however, the
BKUP_FLT bit remains set until either the SHDN pin is set
high (all registers reset) or register bits POR_RESET or
BUFLT_RST are set. See the Shutdown Mode section for
details. During backup, the external thermistor network
is monitored for battery presence.
SYSTEM LOAD
BACKUP LOAD (DCOUT)
DCIN
0V
CURRENT FLOW
BATTERY CHARGE MODE
Figure 2 shows the charge path to charge a battery. Cur-
OFF
ON
ON
BATTERY
rent is pulled from the supply input to charge the battery.
At the same time, the input supply provides power to
both the system load and the backup load. The battery
is isolated from the load at all times so it cannot affect
UVLO
SET POINT
INID
DCDIV
BATID
LTC4110
CHGFET
DCHFET
charger terminations algorithms.
If we ignore battery chemistry for a moment, as far as the
LTC4110 charger is concerned, there are only two basic
Figure 1. Backup Mode Operation
4110 F01
charge modes. When the TYPE pin selects a standard bat-
tery mode, charge termination is controlled by the LTC4110
4110fb
13
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。