- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
DCIN
SYSTEM LOAD
BACKUP LOAD
current sense resistor (R SNS(BAT) ) and CSP/CSN pin resis-
tors. The constant voltage (?oat voltage) is programmed
to one of four values (4.2V, 8.4V, 12.6V, 16.8V) depending
ON
OFF
OFF
on the number of series cells using the SELC pin and can
be adjusted ±0.3V/cell with the V CHG pin. If adjusted, the
CURRENT FLOW
INID
LTC4110
BATID
CHGFET
DCHFET
BATTERY
auto recharge threshold and overvoltage threshold will
track proportionally.
The charge cycle begins when the supply input is present
as sensed by the DCDIV pin and DCIN above UVLO, the
battery cell voltage is below the auto recharge threshold
(95% of the programmed ?oat voltage; see V AR ), thermis-
4110 F02
Figure 2. Charge Mode Operation
for the battery chemistry selected. Speci?cally the TIMER
pin becomes active and used to detect faults conditions or
terminate the charge cycle itself as needed. Smart battery
SMBus charge control commands are still honored if any
are sent at any time. A smart battery can safely function
in a standard battery mode if identical in chemistry and
voltage con?guration as the standard battery. When the
TYPE pin selects a smart battery mode, this simply disables
the TIMER pin and its function in charge termination. The
smart battery is able to restart or terminate a charge cycle
at any time using charge commands over the SMBus. This
mode also enables smart battery wake-up and watchdog
functions based on t TIMEOUT per the smart battery stan-
dards. However it is not recommended to use a standard
battery with a LTC4110 con?gured for smart battery mode
operation. You can shorten battery life, damage or destroy
the battery. In the extreme case this can cause an explosion
since no charge termination mechanisms are active.
The following sections explain detailed operation for each
charge mode as selected by the TYPE pin.
STANDARD LI-ION/POLYMER BATTERY CHARGE MODE
The charger is programmed for standard Li-Ion batteries by
connecting the TYPE pin to GND. During Li-Ion charging,
the LTC4110 operates as a high ef?ciency, synchronous,
PWM ?yback battery charger with constant-current and
constant ?oat voltage regions of operation. The constant-
charge current is programmed by the combination of a
resistor (R CHG ) from the I CHG pin to ground, a battery
tor temperature is within ideal limits, COLD, under range
(see SafetySignal Decoder section) or is optioned out and
the register bit CHARGE_INHIBIT is cleared (see Tables 6
and 7 for register details).
Soft-start ramps the charge current at a rate set by the
capacitor on the I TH pin. When charging begins, the pro-
grammable timer initiates timing and the CHGb (GPIO1
pin) status output is pulled LOW. An external capacitor
on the TIMER pin, along with the current set by the total
series resistance connected to the V REF pin, sets the total
charge time.
If the battery voltage is less than the 3.0V/cell bulk charge
threshold (V BC ), the charger will begin with a precondition-
ing trickle charge current. The trickle current is programmed
by the resistor (R PCC ) from the I PCC pin to ground. During
preconditioning trickle charging, if the battery voltage
stays below the bulk charge threshold (V BC ) 25% of the
programmed bulk charge time, the battery may be defective
and the charge sequence will be terminated immediately.
To indicate this fault, the CHGb (GPIO1 pin) becomes high
impedance, the CHG_STATE_0 and CHG_STATE_1 register
bits will be set low and CHG_FLT register bit will be set
high. Charge is terminated and the timer reset until the
fault is cleared by the RESET_TO_ZERO or POR_RESET
SMBus write commands, SHDN pin toggle or the battery
removed and replaced. Removing the supply input will
not clear the fault if the battery is present.
If the battery voltage exceeds 107.5% (V BOV ) of the
programmed ?oat voltage during any stage of charge,
the charger pauses until the voltage drops below the
hysteresis (V BOVH ). The timer is not stopped and no fault
is indicated.
4110fb
14
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。