- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
PIN FUNCTIONS
DCIN (Pin 1): External DC Power Sense Input. Provides a
control input and supply for the main supply ideal diode
smart battery or Li-Ion battery is in any phase of charging
or when lead acid battery charge current is >C/x where:
function.
CLN (Pin 2): Current Limit Sense Negative Input. See
x =
C
I CHG
?5
CLP pin.
CLP (Pin 3): Current Limit Sense Positive Input. This pin
and the CLN pin form a differential input that senses volt-
age on an external resistor for reverse current entering the
power source while in low loss calibration mode. Should
the current approach reversal, this function will terminate
calibration. An RC ?lter may be required to ?lter out system
load noise. Connect both CLP and CLN pins to GND to
disable this function. A differential voltage of >1V between
the CLP and CLN pins may damage the device.
ACPDLY (Pin 4): ACPb Delay Control Pin. A capacitor
connected from ACPDLY to GND and a resistor from
V REF to GND programs delay in the ACPb pin high-to-low
transition. Open if minimum delay is desired.
DCDIV (Pin 5): AC Present Detection Input. Backup
operation is invoked when the system power voltage,
divided by an external resistor divider, falls below the
threshold of this pin.
SHDN (Pin 6): Active High Shutdown/Reset Control Logic
Input. Forces micropower shutdown mode if high when
DCIN supply is removed. Forces all registers to reset if high
when DCIN supply is present. Normally tied to ground.
Internal pin pull-up current.
SDA (Pin 7): SMBus Bidirectional Data Signal. Connect
to V DD when not in use.
SCL (Pin 8): SMBus Clock Signal Input From SMBus Host.
Connect to V DD when not in use.
GPIO1 (Pin 9): General Purpose I/O or Charge Status Pin. A
logic-level I/O bit port that is con?gurable as a host-driven
input/output port or as a battery charge status output (CHGb)
(See C/x Charge Termination section for more details).
If the No SMBus option is selected with the SELA pin,
the GPIO1 pin defaults as battery charge status. Refer
to Table 5a.
GPIO2 (Pin 10): General Purpose I/O Pin. A logic-level I/O bit
port that is con?gurable as a host-driven input/output port
or as a battery undervoltage status output (BKUP_FLTb)
with an open-drain N-MOSFET that is asserted low only
while in backup mode if the battery’s average cell voltage
drops below voltage programmed by the V DIS pin. If the
No SMBus option is selected with the SELA pin, then the
GPIO2 pin defaults as battery undervoltage status. Refer
to Table 5c.
GPIO3 (Pin 11): General Purpose I/O Pin. A logic-level I/O
bit port that is con?gurable as a host-driven input/output
port or as a calibration complete status output (CAL_COM-
PLETEb) with an open-drain N-MOSFET that is asserted
low when calibration has been completed. If the SELA pin
is programmed for no SMBus use then the status output
is charge fault (CHGFLTb) instead of calibration complete.
Refer to Table 5e.
SELA (Pin 12): SMBus Address Selection Input. Selects
the LTC4110 SMBus address to facilitate redundant backup
systems when standard batteries are used. Connect to
GND for 12h, V DD for 28h and the V REF pin for 20h. When
a smart battery is selected by the TYPE pin, the SELA pin
must be connected to GND to select address 12h. If the
SMBus is not used or to force all GPIOs to status mode
upon power-up, connect pin to a typically 0.5 ? V REF volt-
age from V REF pin resistor divider. The SMBus address,
if used, will be 12h.
with an open-drain N-MOSFET that is asserted low when any
4110fb
8
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。