- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
system load not be adequate to absorb the current. The
primary protection is accomplished with an external current
sense resistor (R CL ), connected between the CLP and CLN
DCIN
SYSTEM LOAD
BACKUP LOAD
pins, through which the system load current ?ows. When
the voltage across the resistor reaches 10mV (I BDT ) or
less, representing a low forward current, calibration mode
is terminated. The current protection can be completely
CURRENT FLOW
ON
OFF
OFF
BATTERY
disabled by connecting both CLP and CLN pins to GND.
As an alternative where R CL sensing is not an option for
the application, a secondary method is accomplished by
INID
LTC4110
BATID
CHGFET
monitoring the supply voltage through the DCDIV pin.
Once the DCDIV pin voltage goes above V OVP , calibration
mode is terminated. In either case, the CAL_FLT register is
set high and the charge mode is automatically entered to
begin recharging the battery. Both of these protections are
automatically disabled when not in calibration. However,
in calibration, one or the other of these two protective
methods should be used. You can optionally do both.
Failure to implement any form of protection can result in
destructive voltages being generated in the application.
If the calibration cycle fails due to loss of the main power
source a fault condition results that sets the CAL_FLT
register bit and backup mode is entered.
An optional external thermistor network is sampled at
regular intervals to monitor battery temperature and to
detect battery presence. If the thermistor value indicates
a temperature outside of ideal limits (hot or over-range)
the calibration current is halted and the CAL_FLT bit will
be set high. When the thermistor value returns to an ac-
ceptable value (under-range, cold or ideal), charge mode
is automatically entered to begin recharging the battery.
Calibration can be restarted by clearing the CAL_FLT bit
and sending another CAL_START command.
An open thermistor (over-range) indicates absence of a
battery. To defeat the temperature monitoring function, re-
place the thermistor with a resistor to indicate ideal battery
temperature. When a thermistor is not used, the resistor
circuit must be routed through the battery connector if
battery presence detection is required. If the battery should
be removed during calibration, calibration will terminate
and the CAL_FLT read bit will be set high.
DCHFET
4110 F06
Figure 6. Calibration Mode Operation
The CAL_FLT bit can be cleared by writing a one to the
CAL_RESET or POR_RESET registers, or by forcing the
SHDN pin high. The CAL_FLT bit is not cleared by remov-
ing and reapplying the supply input if the battery has
maintained suf?cient voltage (V BAT ≥ 2.7V).
Calibration can start only if the CAL_FLT bit in the
BBuStatus() register is clear. Once the LTC4110 is in cali-
bration state, the following events will stop calibration:
? BKDRV is sensed. The CAL_FLT bit is set.
? A HOT thermistor is sensed. The CAL_FLT bit is set.
? Loss of battery presence is sensed. The CAL_FLT bit is
set.
? The calibration cutoff threshold has been reached.
The CAL_COMPLETE bit is set. The LTC4110 will start
charging based upon the TYPE and SELA pins.
? An OVER_TEMP_ALARM, RESERVED_ALARM, or
TERMINATE_DISCHARGE_ALARM bit in the Alarm-
Warning() register is set. The CAL_FLT bit is set. The
LTC4110 will start charging.
? Loss of AC presence. The CAL_FLT bit is set.
SHUTDOWN MODE
The LTC4110 can be forced into either a micropower
shutdown state or an all logic register reset state with
the SHDN pin.
4110fb
22
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。