- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 26/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
OPERATION
The three I/O outputs, GPIO1, GPIO2 and GPIO3 are digital
I/O pins with two modes of operation.
1) General Purpose I/O
2) Status Reporting
A host can set the mode of each I/O pin with each I/O pin’s
setting independent of the others such that any combination
of status reporting or bit I/O can be implemented. Only a
UVLO or a SHDN event will change the GPIO_n_EN bits
back to default values. If you enable a GPIO pin to report
status output, it overrides the GPIO_n_OUT setting. In
addition, the LTC4110 supports a special power up mode
of status reporting on all 3 IO pins for standalone applica-
tions where it is assumed “no host” exists. This power up
status mode is enabled if the SELA pin is set to 0.5 ? V REF
voltage as developed from V REF pin resistor divider. This
mode does not actually disable the SMBus in any way and
if a host does exist in this power up mode, the host can
reprogram the I/O settings at any time.
All GPIO pins operate as digital inputs at all times regard-
less of the pin settings with pin state reported on the
GPIO_n_IN bits in the BBuStatus() register. However to
actually read digital input data from an external device, you
must disable the GPIO_n_EN bit. Otherwise the input will
simply re?ect the output state assuming external powered
pull-ups exist.
Table 5a. GPIO1 Modes
There are a total of 5 status signals possible. CHGb, C/xb,
BKUP-FLTb, CHG_FLTb, and CAL_COMPLETEb. Each of
these signals is asserted low on the output when they
are true. CHGb is an asserted low signal when either
CHG_STATE_0 or CHG_STATE_1 is set to one. C/xb is
asserted low signal when C/x state in the charge cycle is
reached. This status signal is only available if the TYPE pin
is set to SLA mode and replaces the CHGb status output.
BKUP_FLTb is asserted low when the BKUP_FLT bit is set
to one in the BBuStatus() register. BKUP_FLT is a sticky bit
that is designed to be cleared primarily through the setting
of the BUFLT_RST bit in the BBuControl() register. The value
of this bit does not inhibit charging or calibration functions.
CHG_FLTb is asserted low when the CHG_FLT bit is set to
one in the BBuStatus() register. CAL_COMPLETEb bit is
asserted low when the conditions of successful calibra-
tion cycle are met. CAL_COMPLETEb status output can
be used as an interrupt to a host for the purpose of help
implementing a simple gas gauge function or capacity
veri?cation function with a standard battery. However, if the
LTC4110 is set up in no host mode, CAL_COMPLETEb as a
status signal is not considered usable since it is assumed
there is no host to enable calibration mode. Therefore the
CHG_FLTb signal is substituted for CAL_COMPLETEb as
the status output signal. Table 5 describes the speci?c
modes and status signal options of each GPIO pin.
GPIO_1_EN
HOST PROGRAMMED BIT SETTINGS
GPIO_1_OUT
GPIO_1_CHG
GPIO_1 MODE
DATA
NOTE
0
1
1
1
0
X
0
1
0
1
0
0
Digital Input
Status Output
Digital Output
Digital Output
Input Data
CHGb
0
1
GPIO_1_IN
With Pull-Up
With Pull-Up
With Pull-Up
Table 5b. GPIO1 Power Up Mode (SELA = 0.5 ? V REF )
GPIO_1_EN
FORCED BIT SETTINGS
GPIO_1_OUT
GPIO_1_CHG
TYPE = SLA
GPIO_1 MODE
DATA
NOTE
1
1
X
X
1
1
0
1
Status Output
Status Output
CHGb
C/xb
With Pull-Up
With Pull-Up
4110fb
26
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。