- 您现在的位置：买卖IC网 > PDF目录16296 > LTC4110EUHF#PBF (Linear Technology)IC BATTERY BACKUP MANAGER 38-QFN PDF资料下载
参数资料
| 型号： | LTC4110EUHF#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 40/52页 |
| 文件大小： | 0K |
| 描述： | IC BATTERY BACKUP MANAGER 38-QFN |
| 标准包装： | 52 |
| 功能： | 备份管理 |
| 电池化学： | 铅酸，锂离子，锂聚合物，镍镉，镍氢，超级电容器 |
| 电源电压： | 4.5 V ~ 19 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 38-WFQFN 裸露焊盘 |
| 供应商设备封装： | 38-QFN（5x7） |
| 包装： | 管件 |
| 产品目录页面： | 1341 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
LTC4110
APPLICATIONS INFORMATION
where
V CUTOFF = adjusted cutoff threshold voltage
V CAL /V DIS = voltage on V CAL or V DIS pin
V BGR =1.220V
The resistor divider connected to V REF pin will affect timer.
See the Programming Charge Time with TIMER and V REF
Pins section for more details.
PROGRAMMING CHARGE TIME WITH TIMER AND
V REF PINS
Charge time limits for Li-Ion batteries can be programmed
by selection of capacitance on the TIMER pin, but is
dependent upon resistance on the V REF pin. Typical pro-
grammed bulk charge times range from 2 to 12 hours
and is set as follows:
If the TYPE pin is set for SLA/LEAD ACID or any nickel
based smart battery, the TIMER pin is not used. You can
ground the TIMER pin. Furthermore, if there is no need
of any timer function and there is no need of any voltage
divider from V REF to ground, you must still keep a load on
the V REF pin between 10μA and 25μA. It is recommended
you place a 49.9k load resistor from V REF to ground.
CHARGING BATTERIES OVER 12 HOURS
In situations where required bulk charge time cycle will
exceed the 12 hour time limit imposed by the charge TIMER
pin, you have two options. You can have an SMBus host
clear the CHG_FLT bit and force start another charge cycle
or you can switch to a smart version of the same battery.
If you chose the former, reduce the TIMER pin time to
about 2/3 of the actual time required. This will result in
faster termination in the second cycle and with autorestart
C TIMER (F) =
T(Hrs)
(944 ? R VREF ( Ω ))
cycles when V AR is tripped. If you choose the smart bat-
tery option, the smart battery itself safely controls charge
termination. Bulk charge can last as long as necessary
As an example if R VREF = 113k and the desired bulk charge
time limit is ?ve hours then C TIMER = 47nF. See F TMR
which directly affects the 944 constant in the Electrical
Characteristics Table for the tolerance.
Avoid capacitors with high leakage currents. The V REF
pin load resistor range is 49k to 125k or 10μA to 25μA of
load current. At 125k the maximum capacitance on V REF
is limited to a maximum of 50pF to maintain suf?cient AC
stability for the internal ampli?er. At 49k the maximum is
125pF. The maximum capacitance is inversely proportional
to the resistance.
The voltage (V REF ) on the V REF pin can be used as a
precision voltage for other uses with some limitations.
The total V REF pin current must not exceed 25μA and the
capacitance must be limited as discussed above. Load
to charge the battery to 100%. No host is required to do
anything, as the battery will maintain its full charge state
using its SMBus charge commands.
PROGRAMMING AC PRESENT INDICATION DELAY
TIME WITH ACPDLY AND V REF PINS
When the main supply, DCIN, returns after a power failure
the ACPb pin is driven low to indicate presence of main
power. This transition can be delayed to allow time for the
system to stabilize before actions are taken by the system
based on this pin status. The high to low transition only
delay on the ACPb pin can be programmed by selection
of capacitance on the ACPDLY pin, but is dependent upon
resistance on the V REF pin. Typical programmed delay times
range from 10ms to 200ms and is set as follows:
current ?uctuations will modulate the programmed charge
time. In shutdown mode V REF will drop to 0V.
C ACPDLY (F) =
T(s)
2 ? R VREF ( Ω )
In some applications a divided down V REF voltage is needed
to program the SELA, SELC, TYPE, V CHG , V CAL and V DIS
pins. This is easily implemented by use of a resistor divider
connected from V REF to GND that sets the V REF pin current
As an example if R VREF = 113k and the desired delay time
is 105ms then C TIMER = 470nF. See t AC in the Electrical
Characteristics Table for the tolerance.
instead of a single resistor.
4110fb
40
相关PDF资料 |
PDF描述 |
|---|---|
| 3-6754412-6 | CA,XG,MTRJ-SC |
| ECO-S2DB102EA | CAP ALUM 1000UF 200V 20% SNAP |
| 3-6754411-6 | CA,XG,MTRJ-SC |
| RCM10DRYI-S13 | CONN EDGECARD 20POS .156 EXTEND |
| ECO-S2WB181DA | CAP ALUM 180UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC4110EUHF-TR | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
发布紧急采购，3分钟左右您将得到回复。