- 您现在的位置：买卖IC网 > Datasheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008 Datasheet资料下载
参数资料
| 型号： | MAX11008EVC16 |
| 厂商： | Maxim Integrated |
| 文件页数： | 47/67页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT MAX11008 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页当前第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
Set FIFOSTAT to 1 to use the ALARM output to monitor
the data flow of the FIFO while in LUT streaming mode
or message mode. See the LUT Streaming Mode and
Message Mode sections for more information on these
modes of operation and how to use the ALARM output
for FIFO flow control.
Set ADCMON to 1 to copy ADC conversion results into
the FIFO where it can be read out through the serial
interface. See the ADC Monitoring Mode section for
more information on reading conversion results from
the FIFO. ADCMON and AVGMON cannot be active at
the same time.
Program PG_SET[1:0] to set the channel 1 and channel
2 current-sense amplifier gain (see Table 11c).
Program CKSEL[1:0] to set the conversion and acquisi-
Program ADCREF[1:0] to establish the source of the
ADC reference (see Table 11e). Program the
DACREF[1:0] to establish the source of the DAC refer-
ence (see Table 11f). See the ADC and DAC
References section for more information on configuring
the data converter references.
Alarm Software Configuration Register (ALMSCFIG)
(Read/Write)
Configure the software alarm functions with bits D[11:0]
in the Alarm Software Configuration register (see Table
12). Bits D[15:12] are don’t-care bits.
Set A_AVG to 1 to enable the APC averaging and filter-
ing function for channel 1 and channel 2. The
APCSRC_ field in the SCFG register controls the source
of the sample.
tion timing clock modes (see Table 11d). See the
Internally Timed Acquisitions and Conversions section
for detailed descriptions of each clock mode.
Table 7. High Temperature Threshold Register
DATA BITS
D[15:12]
BIT NAME
Unused
RESET STATE
X
Unused bits.
FUNCTION
D[11:D0]
THI[11:0]
0111 1111 1111 High temperature threshold data bits.
X = Don’t care.
Table 8. Low Temperature Threshold Register
DATA BITS
D[15:12]
D[11:0]
BIT NAME
Unused
TLO[11:0]
RESET STATE
X
1000 0000 0000
FUNCTION
Unused bits.
Low temperature threshold data bits.
X = Don’t care.
Table 9. High Current Threshold Register
DATA BITS
D[15:12]
BIT NAME
Unused
RESET STATE
X
Unused bits.
FUNCTION
D[11:0]
IHI[11:0]
1111 1111 1111 High current threshold data bits.
X = Don’t care.
Table 10. Low Current Threshold Register
DATA BITS
D[15:12]
BIT NAME
Unused
RESET STATE
X
Unused bits.
FUNCTION
D[11:0]
X = Don’t care.
ILO[11:0]
0000 0000 0000 Low current threshold data bits.
______________________________________________________________________________________
47
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11014BGTM+T | IC RF MESFET AMP 48-TQFN-EP |
| MAX12000ETB+T | IC AMP GPS FRONT 1575MHZ 10TDFN |
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11008EVKIT+ | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1100CWG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1101 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA |
| MAX11014 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11014_08 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
发布紧急采购，3分钟左右您将得到回复。