- 您现在的位置：买卖IC网 > Datasheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008 Datasheet资料下载
参数资料
| 型号： | MAX11008EVC16 |
| 厂商： | Maxim Integrated |
| 文件页数： | 61/67页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT MAX11008 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
FIFOEMP is set to 1 when the FIFO is empty. Once data
is placed into the FIFO, FIFOEMP is set to 0.
When in ADC monitoring mode, FIFOOVER is set to 1
when a FIFO overflow occurs. FIFOOVER remains at 1,
even if the FIFO is subsequently read and no longer
full. FIFOOVER is reset by reading the Flag register.
When in LUT streaming mode or message mode, the
FIFO is not permitted to overflow and FIFOOVER then
denotes when the FIFO is full. FIFOOVER is set to 1
Table 19. PGA Calibration Control Register
when the FIFO is full and immediately returns to 0 once
a data word is moved out of the FIFO.
HIGHI_ is set to 1 when the individual channel 1 and
channel 2 current-sense measurements exceed the
individual channel 1 and channel 2 high current thresh-
old and returns to 0 after the Flag register is read.
HIGHI2 is replaced by HIGHT2 when the INTEMP2 bit
is set in the Alarm Hardware Configuration register.
DATA BITS
D[15:3]
BIT NAME
Unused
RESET STATE
X
Unused bits.
FUNCTION
Acquisition/tracking bit. Set to 0 to force the next current-sense calibration
D2
TRACK
0
to run in acquisition mode. Set to 1 to force the next calibration to run in
tracking mode. Set TRACK to 0 the first time through a calibration.
D1
DOCAL
0
Single calibration select bit. Set to 1 perform single or self-timed
calibrations of PGA1 and PGA2. DOCAL resets to 0 after calibration.
Self-timed calibration select bit. Set to 1 to perform calibrations of PGA1
D0
SELFTIME
0
and PGA2 on a self-timed periodic basis (approximately every 13ms).
When set to 0, calibrations only occur when DOCAL is set to 1.
X = Don’t care.
NA = Not applicable.
Table 20. ADC Conversion Register
DATA BITS
D[15:8]
D7
D6
D5
D4
D3
D2
D1
D0
BIT NAME
Unused
CONCONV
ADCIN2
CS2
EXTEMP2
ADCIN1
CS1
EXTEMP1
INTEMP
RESET STATE
X
0
0
0
0
0
0
0
0
FUNCTION
Unused bits.
Continuous conversion select bit. Set to 1 to perform continuous
conversions of the selected channels.
ADCIN2 conversion select bit.
CS2 current-sense conversion select bit.
External temperature sensor 2 conversion select bit.
ADCIN1 conversion select bit.
CS1 current-sense conversion select bit.
External temperature sensor 1 conversion select bit.
Internal temperature sensor conversion select bit.
X = Don’t care.
NA = Not applicable.
______________________________________________________________________________________
61
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11014BGTM+T | IC RF MESFET AMP 48-TQFN-EP |
| MAX12000ETB+T | IC AMP GPS FRONT 1575MHZ 10TDFN |
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11008EVKIT+ | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1100CWG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1101 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA |
| MAX11014 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11014_08 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
发布紧急采购，3分钟左右您将得到回复。