- 您现在的位置：买卖IC网 > Datasheet目录470 > MAX11008EVC16 (Maxim Integrated)EVAL KIT MAX11008 Datasheet资料下载
参数资料
| 型号： | MAX11008EVC16 |
| 厂商： | Maxim Integrated |
| 文件页数： | 53/67页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT MAX11008 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页当前第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
Dual RF LDMOS Bias Controller with
Nonvolatile Memory
Table 13. Software Configuration Register
DATA BITS
D15*
D[14:12]*
BIT NAME
T2AVGCTL
T2LIMIT[2:0]
RESET STATE
0
000
FUNCTION
Channel 2 averaging-equation bit. This bit controls the averaging equation
for channel 2 while the device is in tracking mode. See Table 13a.
Channel 2 difference-limiter bits. Set T2LIMIT[2:0] to enable the difference
limiter for channel 2 temperature averaging. See Table 13b.
Channel 2 LDAC control bit. Set to 0 to load calculation results into the DAC
D11
LDAC2
0
2 input and output registers. Set to 1 to load calculation results into the
DAC 2 input register only.
D10
TCOMP2
0
Channel 2 temperature compensation enable bit. Set to 1 to allow V GATE2
calculations to be triggered by channel 2 temperature measurements.
Channel 2 APC parameter compensation enable bit. Set to 1 to allow
D9
APCCOMP2
0
V GATE2 calculations to be triggered by channel 2 current-sense
measurements or APC2 parameter changes.
Channel 2 temperature sensor select bit. Set to 0 to use the channel 2
D8
TSRC2
0
external temperature sensor as the source of the temperature parameter for
V GATE2 calculations. Set to 1 to use the internal temperature sensor.
D[7:6]
APCSRC2[1:0]
00
Channel 2 APC parameter select bits. Set APCSRC2[1:0] to select the data
source for V GATE2 calculations. See Table 13c.
Channel 1 LDAC control bit. Set to 0 to load calculation results into the DAC
D5
LDAC1
0
1 input and output registers. Set to 1 to load calculation results into the
DAC 1 input register only.
D4
TCOMP1
0
Channel 1 temperature compensation enable bit. Set to 1 to allow V GATE1
calculations to be triggered by channel 1 temperature measurements.
Channel 1 APC parameter compensation enable bit. Set to 1 to allow
D3
APCCOMP1
0
V GATE1 calculations to be triggered by channel 1 current-sense
measurements or APC1 parameter changes.
Channel 1 temperature sensor select bit. Set to 0 to use the channel 1
D2
TSRC1
0
external temperature sensor as the source of the temperature parameter for
V GATE1 calculations. Set to 1 to use the internal temperature sensor.
D[1:0]
APCSRC1[1:0]
00
Channel 1 APC parameter select bits. Set APCSRC1[1:0] to select the data
source for V GATE1 calculations. See Table 13c.
X = Don’t care.
*Write only.
______________________________________________________________________________________
53
相关PDF资料 |
PDF描述 |
|---|---|
| MAX11014BGTM+T | IC RF MESFET AMP 48-TQFN-EP |
| MAX12000ETB+T | IC AMP GPS FRONT 1575MHZ 10TDFN |
| MAX12005ETM+T | IC SATELLITE IF SWITCH 48-TQFN |
| MAX1385BUTM+ | IC RF LDMOS BIAS CNTRLR 48-TQFN |
| MAX1470EUI+T | IC RECEIVER 315MHZ 28-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX11008EVKIT+ | 功能描述:放大器 IC 开发工具 MAX11008 Eval Kit RoHS:否 制造商:International Rectifier 产品:Demonstration Boards 类型:Power Amplifiers 工具用于评估:IR4302 工作电源电压:13 V to 23 V |
| MAX1100CWG | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1101 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA |
| MAX11014 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
| MAX11014_08 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Automatic RF MESFET Amplifier Drain-Current Controllers |
发布紧急采购，3分钟左右您将得到回复。