- 您现在的位置：买卖IC网 > PDF目录98009 > MAX14830ETM+ (MAXIM INTEGRATED PRODUCTS INC) SERIAL COMM CONTROLLER, QCC48 PDF资料下载
参数资料
| 型号： | MAX14830ETM+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SERIAL COMM CONTROLLER, QCC48 |
| 封装： | 7 X 7 MM, ROHS COMPLIANT, TQFN-48 |
| 文件页数： | 19/68页 |
| 文件大小： | 2356K |
| 代理商： | MAX14830ETM+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
MAX14830
Quad Serial UART with 128-Word FIFOs
and Internal Oscillator
26
Echo suppression can operate simultaneously with auto
transceiver direction control (Figure 15).
Auto Hardware Flow Control
The MAX14830 is capable of automatic hardware (RTS
and CTS) flow control without the need for host proces-
sor intervention. When AutoRTS control is enabled,
the MAX14830 automatically controls the RTS hand-
shake without the need for host processor intervention.
AutoCTS flow control separately turns the MAX14830’s
transmitter on and off based on the CTS_ input. AutoRTS
and AutoCTS flow control are independently enabled
through FlowCtrl[1:0].
AutoRTS Control
AutoRTS flow control ensures that the Receive FIFO does
not overflow by signaling to the far end UART to stop
data transmission. The MAX14830 does this automatical-
ly by controlling RTS_. AutoRTS flow control is enabled
through FlowCtrl[0]: AutoRTS. The HALT and RESUME
levels determine the threshold levels at which RTS_ is
asserted and deasserted. HALT and RESUME are pro-
grammed in FlowLvl. With differing HALT and RESUME
levels, hysteresis can be defined for the RTS_ transitions.
When the RxFIFO fill level reaches the HALT level
(FlowLvl[3:0]), the MAX14830 deasserts RTS_. RTS_
remains deasserted until the RxFIFO is emptied and the
number of words falls to the RESUME level.
Interrupts are not generated when the HALT and
RESUME levels are reached. This allows the host control-
ler to be completely disengaged from RTS flow control
management.
AutoCTS Control
When AutoCTS flow control is enabled, the UART auto-
matically starts transmitting data when the CTS_ input
is logic-level low and stops transmitting when CTS_ is
logic-high. This frees the host processor from manag-
ing this timing-critical flow control task. AutoCTS flow
control is enabled through FlowCtrl[1]: AutoCTS. During
AutoCTS flow control, the CTS interrupt works normally.
Set the IRQEn[7]: CTSIntEn to 0 to disable CTS interrupts
then ISR[7]: CTSInt is fixed to logic 0 and the host does
not receive interrupts from CTS_. If CTS_ is set high dur-
ing transmission the MAX14830 completes transmission
of the current word and halts transmission afterwards.
Turn the transmitter off by setting MODE1[1] to 1 before
enabling AutoCTS control.
FIFO Interrupt Triggering
Receive and Transmit FIFO fill-dependent interrupts are
generated if FIFO trigger levels are defined. When the
number of words in the FIFOs reach or exceed a trigger
level, as programmed in FIFOTrgLvl, an ISR[3] or ISR[4]
interrupt is generated. There is no relationship between
the trigger levels and the HALT or RESUME levels.
The FIFO trigger level can, for example, be used for a
block data transfer, since it gives the host an indication
when a given block size of data is available for reading in
the Receive FIFO or available for transfer to the Transmit
FIFO.
Auto Software (XON/XOFF) Flow Control
When auto software flow control is enabled, the
MAX14830 recognizes and/or sends predefined XON/
XOFF characters to control the flow of data across the
asynchronous serial link. Automatic flow works autono-
mously and does not involve host intervention, similar
to auto hardware flow control. To reduce the chance of
receiving corrupted data that equals a single-byte XON
or XOFF character, the MAX14830 allows for double
wide (16-bit) XON/XOFF characters. XON and XOFF are
programmed into the XON1, XON2 and XOFF1, XOFF2
registers.
FlowCtrl[7:3] are used for enabling and configuring auto
software flow control. An ISR[1] interrupt is generated
when XON or XOFF are received and details are found
in SpclCharInt. The IRQ can be masked by setting
IRQEn[1]: SpclChrIEn to 0.
Software flow control consists of transmitter control and
receiver overflow control, which can operate indepen-
dently of one another.
Figure 15. Half-Duplex with Echo Suppression
TX
LOGIC
TRANSMITTER
TX_
DI
D
B
A
R
DE
RE
RO
RTS_
RX_
ECHO
SUPPRESSION
RECEIVER
Rx FIFO
Tx FIFO
MAX14840E
MAX14830
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3624AETJ+ | 312.5 MHz, OTHER CLOCK GENERATOR, QCC32 |
| MAX3638ETM+ | 800 MHz, OTHER CLOCK GENERATOR, QCC48 |
| MAX3679CTJ+ | 625 MHz, OTHER CLOCK GENERATOR, QCC32 |
| MAX7329AUP+ | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
| MAX7329AAP+ | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX14830ETM+ | 功能描述:UART 接口集成电路 Quad Serial UART w/128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX14830ETM+T | 功能描述:UART 接口集成电路 Quad Serial UART w/128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX14830EVKIT# | 功能描述:界面开发工具 MAX14830 Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX14830EVKIT+ | 制造商:Maxim Integrated Products 功能描述:QUAD UART EV-KIT WITH IO-LINK AND MULTIPROTOCOL - Boxed Product (Development Kits) |
| MAX1483C/D+ | 功能描述:RS-485接口IC low-power transceivers for RS-485 and RS-422 communication RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。