- 您现在的位置：买卖IC网 > PDF目录98009 > MAX14830ETM+ (MAXIM INTEGRATED PRODUCTS INC) SERIAL COMM CONTROLLER, QCC48 PDF资料下载
参数资料
| 型号： | MAX14830ETM+ |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SERIAL COMM CONTROLLER, QCC48 |
| 封装： | 7 X 7 MM, ROHS COMPLIANT, TQFN-48 |
| 文件页数： | 60/68页 |
| 文件大小： | 2356K |
| 代理商： | MAX14830ETM+ |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页当前第60页第61页第62页第63页第64页第65页第66页第67页第68页
MAX14830
Quad Serial UART with 128-Word FIFOs
and Internal Oscillator
63
Acknowledge Bits
Data transfers are acknowledged with an acknowledge
bit (ACK) or a not-acknowledge bit (NACK). Both the
master and the MAX14830 generate ACK bits. To gener-
ate an ACK, pull SDA low before the rising edge of the
ninth clock pulse and keep it low during the high period
of the ninth clock pulse (Figure 26). To generate a NACK,
leave SDA high before the rising edge of the ninth clock
pulse and keep it high for the duration of the ninth clock
pulse. Monitoring for NACK bits allows for detection of
unsuccessful data transfers.
Applications Information
Startup and Initialization
The MAX14830 is initialized following power-up or a
hardware or software reset (Figure 27). Check that the
MAX14830 is ready for operation after a power-up or
reset by monitoring the IRQ output, if interrupt driven
operation is employed.
In polled mode, repeatedly read a known register until
the expected contents are returned.
Low-Power Operation
To reduce the power consumption during normal opera-
tion, the following techniques can be adopted:
DonotusetheinternalPLL.Thissavesthemostpower
of the options listed here. Disable and bypass the PLL.
Use an external clock source. Of the three clocking
sources, the internal oscillator consumes the most
power. The least amount of power is consumed when
an external clock signal is used.
Use an external 1.8V supply at V18. This saves the
power dissipated in the internal 1.8V linear regulator
for the 1.8V core supply. Disable the internal regulator
by connecting LDOEN to DGND.
Keepinternalclockratesaslowaspossible.
UsealowvoltageontheVA supply.
Interrupts and Polling
Monitor the MAX14830 by polling the ISR register or
by monitoring the IRQ output. In polled mode, the IRQ
physical interrupt output is not used and the host control-
ler polls the ISR register at frequent intervals to establish
the state of the MAX14830.
Alternatively, the physical interrupt, IRQ, of the MAX14830
can be used to interrupt the host controller at specified
events, making polling unnecessary. The IRQ output is
an open-drain output that requires a pullup resistor to VL.
Logic-Level Translation
The MAX14830 can be directly connected to transceivers
and controllers that have different supply voltages. The VL
input defines the logic voltage levels of the controller inter-
face while the VEXT voltage defines the logic of the trans-
ceiver interface. This ensures flexibility when selecting a
controller and transceiver. Figure 28 is an example of a
setup when the controller, transceiver, and the MAX14830
are powered by three different supplies.
IO-Link Application
The Typical Operating Circuit shows a four-part IO-link
master circuit with SPI control on the MAX14830 and the
IO-link transceivers.
Figure 26. Acknowledge Bits
Figure 27. Startup and Initialization Flow Chart
NOT ACKNOWLEDGE
ACKNOWLEDGE
1
2
8
9
SDA
SCL
S
POWER-UP/
RST INPUT PULLED HIGH
CONFIGURE
CLOCKING
YES
NO
CONFIGURE
FIFO CONTROL
CONFIGURE
FLOW CONTROL
CONFIGURE
GPIOs
START
COMMUNICATION
CONFIGURE
MODES
IRQ IS HIGH?
OR
DIVLSB READ
SUCCESSFULLY?
ENABLE
INTERRUPTS
相关PDF资料 |
PDF描述 |
|---|---|
| MAX3624AETJ+ | 312.5 MHz, OTHER CLOCK GENERATOR, QCC32 |
| MAX3638ETM+ | 800 MHz, OTHER CLOCK GENERATOR, QCC48 |
| MAX3679CTJ+ | 625 MHz, OTHER CLOCK GENERATOR, QCC32 |
| MAX7329AUP+ | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
| MAX7329AAP+ | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX14830ETM+ | 功能描述:UART 接口集成电路 Quad Serial UART w/128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX14830ETM+T | 功能描述:UART 接口集成电路 Quad Serial UART w/128-Word FIFOs RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| MAX14830EVKIT# | 功能描述:界面开发工具 MAX14830 Eval Kit RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| MAX14830EVKIT+ | 制造商:Maxim Integrated Products 功能描述:QUAD UART EV-KIT WITH IO-LINK AND MULTIPROTOCOL - Boxed Product (Development Kits) |
| MAX1483C/D+ | 功能描述:RS-485接口IC low-power transceivers for RS-485 and RS-422 communication RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。