- 您现在的位置：买卖IC网 > PDF目录5131 > MAX1545ETL+T (Maxim Integrated Products)IC QUICK-PWM DUAL-PHASE 40-TQFN PDF资料下载
参数资料
| 型号： | MAX1545ETL+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 16/43页 |
| 文件大小： | 0K |
| 描述： | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Quick-PWM™ |
| 应用： | 控制器，Intel Pentium? IV |
| 输入电压： | 2 V ~ 28 V |
| 输出数： | 1 |
| 输出电压： | 0.6 V ~ 1.85 V |
| 工作温度： | -40°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘 |
| 供应商设备封装： | 40-TQFN-EP（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页
Dual-Phase, Quick-PWM Controllers for
Programmable CPU Core Power Supplies
Pin Description (continued)
PIN
31
32
33
34
35
36
37
38
39
40
NAME
PGND
DLS
DHS
LXS
BSTS
V+
CMP
CMN
CSN
CSP
FUNCTION
Power Ground. Ground connection for low-side gate drivers DLM and DLS.
Secondary Low-Side Gate-Driver Output. DLS swings from PGND to V DD . DLS is forced high after the
MAX1519/MAX1545 power down.
Secondary High-Side Gate-Driver Output. Swings LXS to BSTS.
Secondary Inductor Connection. LXS is the internal lower supply rail for the DHS high-side gate
driver.
Secondary Boost Flying Capacitor Connection. An optional resistor in series with BSTS allows the
DHS pullup current to be adjusted.
Battery Voltage-Sense Connection. Used only for PWM one-shot timing. DH_ on-time is inversely
proportional to input voltage over a range of 4V to 28V.
Main Inductor Positive Current-Sense Input
Main Inductor Negative Current-Sense Input
Secondary Inductor Positive Current-Sense Input
Secondary Inductor Negative Current-Sense Input
Detailed Description
Dual 180° Out-of-Phase Operation
The two phases in the MAX1519/MAX1545 operate
180° out-of-phase ( SKIP = REF or high) to minimize
input and output filtering requirements, reduce electro-
magnetic interference (EMI), and improve efficiency.
This effectively lowers component count —reducing
cost, board space, and component power require-
ments—making the MAX1519/MAX1545 ideal for high-
power, cost-sensitive applications.
Typically, switching regulators provide transfer power
using only one phase instead of dividing the power
among several phases. In these applications, the input
capacitors must support high instantaneous current
requirements. The high-RMS ripple current can lower
efficiency due to I 2 R power loss associated with the input
capacitor’s effective series resistance (ESR). Therefore,
the system typically requires several low-ESR input
capacitors in parallel to minimize input voltage
ripple, reduce ESR-related power losses, and to meet
the necessary RMS ripple current rating.
With the MAX1519/MAX1545, the controller shares the
current between two phases that operate 180° out-of-
phase, so the high-side MOSFETs never turn on simul-
taneously during normal operation. The instantaneous
input current of either phase is effectively cut in half,
resulting in reduced input voltage ripple, ESR power
loss, and RMS ripple current (see the Input Capacitor
Selection section). As a result, the same performance
can be achieved with fewer or less expensive input
capacitors.
Transient Overlap Operation
When a transient occurs, the response time of the con-
troller depends on how quickly it can slew the inductor
current. Multiphase controllers that remain 180° out-of-
phase when a transient occurs actually respond slower
than an equivalent single-phase controller. In order to
provide fast transient response, the MAX1519/
MAX1545 support a phase-overlap mode, which allows
the dual regulators to operate in-phase when heavy
load transients are detected, reducing the response
time. After either high-side MOSFET turns off and if the
output voltage does not exceed the regulation voltage
when the minimum off-time expires, the controller simul-
taneously turns on both high-side MOSFETs during the
next on-time cycle. This maximizes the total inductor-
current slew rate. The phases remain overlapped until
the output voltage exceeds the regulation voltage and
after the minimum off-time expires.
After the phase-overlap mode ends, the controller auto-
matically begins with the opposite phase. For example, if
the secondary phase provided the last on-time pulse
before overlap operation began, the controller starts
switching with the main phase when overlap operation
ends.
16
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| EEC40DRYH-S734 | CONN EDGECARD 80POS DIP .100 SLD |
| MAX1544ETL+T | IC QUICK-PWM DUAL-PHASE 40-TQFN |
| SIP21106DVP-28-E3 | IC REG LDO 2.8V .15A SC75-6 |
| 420VXG470MEFCSN35X40 | CAP ALUM 470UF 420V 20% SNAP-IN |
| 160USG3300MEFCSN35X45 | CAP ALUM 3300UF 160V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1546AETL | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1546AETL+ | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Rail/Tube |
| MAX1546AETL+T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel |
| MAX1546AETL-T | 制造商:Maxim Integrated Products 功能描述:DUAL-PHASE, QUICK-PWM CONTROLLER FOR IMVP CPU - Tape and Reel |
| MAX1546ETL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。