参数资料
型号: MCF5235CVM100
厂商: MOTOROLA INC
元件分类: 微控制器/微处理器
英文描述: 32-BIT, 100 MHz, RISC PROCESSOR, PBGA256
封装: MAPBGA-256
文件页数: 18/76页
文件大小: 2665K
代理商: MCF5235CVM100
MOTOROLA
MCF523x Integrated Microprocessor Hardware Specifications
25
PRELIMINARY—SUBJECT TO CHANGE WITHOUT NOTICE
Signal Primary Functions
2.2.11 Queued Serial Peripheral Interface (QSPI)
Table 12 describes QSPI signals.
2.2.12 UART Module Signals
The UART modules use the signals in this section for data. The baud rate clock inputs are not supported.
Table 12. Queued Serial Peripheral Interface (QSPI) Signals
Signal Name
Abbreviation
Function
I/O
QSPI Syncrhonous
Serial Output
QSPI_DOUT
Provides the serial data from the QSPI and can be programmed to be
driven on the rising or falling edge of QSPI_CLK. Each byte is sent
msb first.
This pin can also be configured as GPIO.
O
QSPI Synchronous
Serial Data Input
QSPI_DIN
Provides the serial data to the QSPI and can be programmed to be
sampled on the rising or falling edge of QSPI_CLK. Each byte is
written to RAM lsb first.
This pin can also be configured as GPIO or as I2C data signal
I2C_SDA.
I
QSPI Serial Clock
QSPI_CLK
Provides the serial clock from the QSPI. The polarity and phase of
QSPI_CLK are programmable. The output frequency is programmed
according to the following formula, in which n can be any value
between 1 and 255:
SPI_CLK = fsys/2 ÷ n
This pin can also be configured as GPIO or as I2C clock signal
I2C_SCL.
O
Synchronous
Peripheral Chip Selects
QSPI_CS[1:0] Provide QSPI peripheral chip selects that can be programmed to be
active high or low. QSPI_CS1 can also be configured as SDRAM
clock enable signal SD_CKE.
These pins can also be configured as GPIO.
O
Table 13. UART Module Signals
Signal Name
Abbreviation
Function
I/O
Transmit Serial Data
Output
U2TXD/U1TXD
/U0TXD
Transmitter serial data outputs for the UART modules. The output is
held high (mark condition) when the transmitter is disabled, idle, or in
the local loopback mode. Data is shifted out, lsb first, on this pin at the
falling edge of the serial clock source.
U1TXD can also be configured as Controller Area Network Transmit
data output CAN0TX.
U2TXD can also be configured as Controller Area Network Transmit
data output CAN1TX.
All pins can also be configured as GPIO.
O
相关PDF资料
PDF描述
MC68HC908GZ16MFA 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP48
MC68HC05K3CP 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDIP16
MC68HC11ED0CFN2 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44
MC68HC908GR4AMP 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP32
MC68HC908GR4AVP 8-BIT, FLASH, 8.2 MHz, MICROCONTROLLER, PQFP32
相关代理商/技术参数
参数描述
MCF5235CVM100J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
MCF5235CVM150 功能描述:IC MPU 32BIT COLDF 256-MAPBGA RoHS:否 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:MCF523x 标准包装:330 系列:- 核心处理器:- 芯体尺寸:8/16-位 速度:40MHz 连通性:UART/USART 外围设备:DMA,PWM,WDT 输入/输出数:32 程序存储器容量:- 程序存储器类型:外部程序存储器 EEPROM 大小:- RAM 容量:- 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:100-BQFP 包装:管件
MCF5235CVM150 制造商:Freescale Semiconductor 功能描述:Microprocessor IC
MCF5235CVM150J 功能描述:32位微控制器 - MCU V2CORE 64KSRAM RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
MCF5235CVM150J 制造商:Freescale Semiconductor 功能描述:IC 32-BIT MPU 150 MHz 256-BGA