- 您现在的位置：买卖IC网 > PDF目录17049 > MPC8313E-RDB (Freescale Semiconductor)BOARD PROCESSOR PDF资料下载
参数资料
| 型号： | MPC8313E-RDB |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 91/99页 |
| 文件大小： | 0K |
| 描述： | BOARD PROCESSOR |
| 产品培训模块： | MPC8313E PowerQUICC Processor MPC8314/15 Product Overview |
| 标准包装： | 1 |
| 系列： | PowerQUICC II™ PRO |
| 类型： | MCU |
| 适用于相关产品： | MPC8313E |
| 所含物品： | 参考设计板、软件和说明文档 |
| 相关产品： | MPC8313VRAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313EZQAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313EVRAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313ECZQAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313ECVRAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313CZQAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313CVRAFFB-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313ZQAFF-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313ZQADD-ND - IC MPU POWERQUICC II PRO 516PBGA MPC8313VRAFF-ND - IC MPU POWERQUICC II PRO 516PBGA 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页当前第91页第92页第93页第94页第95页第96页第97页第98页第99页
MPC8313E PowerQUICC II Pro Processor Hardware Specifications, Rev. 4
Freescale Semiconductor
91
This table summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD,
nominal NVDD, 105C.
22.7
Configuration Pin Muxing
The MPC8313E provides the user with power-on configuration options which can be set through the use
of external pull-up or pull-down resistors of 4.7 k
on certain output pins (see customer visible
configuration pins). These pins are generally used as output only pins in normal operation.
While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins
while HRESET is asserted, is latched when PORESET deasserts, at which time the input receiver is
disabled and the I/O circuit takes on its normal function. Careful board layout with stubless connections
to these pull-up/pull-down resistors coupled with the large value of the pull-up/pull-down resistor should
minimize the disruption of signal quality or speed for output pins thus configured.
22.8
Pull-Up Resistor Requirements
The MPC8313E requires high resistance pull-up resistors (10 k
is recommended) on open drain type pins
including I2C, and IPIC (integrated programmable interrupt controller).
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 61. Care must be taken to ensure that these pins are maintained at a valid deasserted
state under normal operating conditions because most have asynchronous behavior and spurious assertion,
which give unpredictable results.
Refer to the PCI 2.2 Specification, for all pull-ups required for PCI.
22.9
JTAG Configuration Signals
Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in
IEEE 1149.1, but is provided on any Freescale devices that are built on Power Architecture technology.
The device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does
not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state
using only the TCK and TMS signals, systems generally assert TRST during power-on reset. Because the
JTAG interface is also used for accessing the common on-chip processor (COP) function, simply tying
TRST to PORESET is not practical.
Table 71. Impedance Characteristics
Impedance
Local Bus, Ethernet,
DUART, Control,
Configuration, Power
Management
PCI Signals
(Not Including PCI
Output Clocks)
PCI Output Clocks
(Including
PCI_SYNC_OUT)
DDR DRAM
Symbol
Unit
RN
42 Target
25 Target
42 Target
20 Target
Z0
RP
42 Target
25 Target
42 Target
20 Target
Z0
Differential
NA
ZDIFF
相关PDF资料 |
PDF描述 |
|---|---|
| STD01W-J | WIRE & CABLE MARKERS |
| STD09W-C | WIRE & CABLE MARKERS |
| STD09W-T | WIRE & CABLE MARKERS |
| MLK1005S18NJ | INDUCTOR MULTILAYER 18NH 0402 |
| STD02W-R | WIRE & CABLE MARKERS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MPC8313E-RDBB | 功能描述:开发板和工具包 - 其他处理器 CPU BOARD VER 2.1 RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MPC8313E-RDBB | 制造商:Freescale Semiconductor 功能描述:; LEADED PROCESS COMPATIBLE:YES; PEAK RE |
| MPC8313E-RDBC | 功能描述:开发板和工具包 - 其他处理器 8313E CPU board Ver 2.2 RoHS:否 制造商:Freescale Semiconductor 产品:Development Systems 工具用于评估:P3041 核心:e500mc 接口类型:I2C, SPI, USB 工作电源电压: |
| MPC8313EVRADD | 制造商:Freescale Semiconductor 功能描述:MPC83XX RISC 32-BIT 90NM 333MHZ 1V/1.8V/2.5V/3.3V 516-PIN TE - Trays |
| MPC8313EVRADDB | 功能描述:微处理器 - MPU PBGA W/ ENCR RoHS:否 制造商:Atmel 处理器系列:SAMA5D31 核心:ARM Cortex A5 数据总线宽度:32 bit 最大时钟频率:536 MHz 程序存储器大小:32 KB 数据 RAM 大小:128 KB 接口类型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作电源电压:1.8 V to 3.3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:FBGA-324 |
发布紧急采购，3分钟左右您将得到回复。