- 您现在的位置：买卖IC网 > PDF目录189004 > NAND512W3A2SN6E 64M X 8 FLASH 3V PROM, PDSO48 PDF资料下载
参数资料
| 型号： | NAND512W3A2SN6E |
| 元件分类： | PROM |
| 英文描述： | 64M X 8 FLASH 3V PROM, PDSO48 |
| 封装： | 12 X 20 MM, ROHS COMPLIANT, PLASTIC, TSOP-48 |
| 文件页数： | 18/51页 |
| 文件大小： | 1009K |
| 代理商： | NAND512W3A2SN6E |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
Numonyx SLC SP 70 nm
Device operations
210403 - Rev 3
6.5
Block erase
Erase operations are done one block at a time. An erase operation sets all of the bits in the
addressed block to ‘1’. All previous data in the block is lost.
An erase operation consists of three steps (refer to Figure 14):
1.
One bus cycle is required to setup the Block Erase command
2.
Only three bus cycles are required to input the block address. The first cycle (A0 to A7)
is not required as only addresses A14 to A25 are valid, A9 to A13 are ignored. In the
last address cycle I/O2 to I/O7 must be set to VIL.
3.
One bus cycle is required to issue the Confirm command to start the P/E/R controller.
Once the erase operation has completed the status register can be checked for errors.
Figure 14.
Block erase operation
6.6
Reset
The Reset command is used to reset the command interface and status register. If the
Reset command is issued during any operation, the operation will be aborted. If it was a
program or erase operation that was aborted, the contents of the memory locations being
modified will no longer be valid as the data will be partially programmed or erased.
If the device has already been reset then the new Reset command will not be accepted.
The Ready/Busy signal goes Low for tBLBH4 after the Reset command is issued. The value
of tBLBH4 depends on the operation that the device was performing when the command was
issued, refer to Table 22 for the values.
I/O
RB
Block Address
Inputs
SR0
ai07593
D0h
70h
60h
Block Erase
Setup Code
Confirm
Code
Read Status Register
Busy
tBLBH3
(Erase Busy time)
相关PDF资料 |
PDF描述 |
|---|---|
| NAND99R3M2AZBB5E | SPECIALTY MEMORY CIRCUIT, PBGA107 |
| NAND99W3M1AZBC5F | SPECIALTY MEMORY CIRCUIT, PBGA137 |
| NANDB9R4N2BZBA5F | SPECIALTY MEMORY CIRCUIT, PBGA149 |
| NANDBAR4N1BZBC5F | SPECIALTY MEMORY CIRCUIT, PBGA137 |
| NANDB9R4N2CZBA5E | SPECIALTY MEMORY CIRCUIT, PBGA149 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NAND512W3A2SN6F | 制造商:Micron Technology Inc 功能描述:512MB NAND FLASH 制造商:Micron Technology Inc 功能描述:NAND - Tape and Reel |
| NAND512W3A2SZA6E | 制造商:Micron Technology Inc 功能描述:SLC NAND Flash Parallel 3V/3.3V 512Mbit 64M x 8bit 12us 63-Pin VFBGA Tray 制造商:Micron Technology Inc 功能描述:NAND - Trays 制造商:Micron Technology Inc 功能描述:MICNAND512W3A2SZA6E 512MB NAND FLASH 制造商:Micron Technology 功能描述:SLC NAND Flash Parallel 3V/3.3V 512Mbit 64M x 8bit 12us 63-Pin VFBGA Tray |
| NAND512W3A2SZA6F | 制造商:Micron Technology Inc 功能描述:SLC NAND Flash Parallel 3V/3.3V 512Mbit 64M x 8bit 12us 63-Pin VFBGA T/R 制造商:Micron Technology Inc 功能描述:NAND - Tape and Reel 制造商:Micron Technology 功能描述:SLC NAND Flash Parallel 3V/3.3V 512Mbit 64M x 8bit 12us 63-Pin VFBGA T/R |
| NAND512W4A0AN6E | 功能描述:闪存 NAND & S.MEDIA FLASH RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| NAND512W4A0AZA6E | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3V/3.3V 512MBIT 32MX16 12US 63VFBGA - Trays |
发布紧急采购，3分钟左右您将得到回复。