- 您现在的位置：买卖IC网 > PDF目录367934 > PH28F640L18T85 (INTEL CORP) StrataFlash Wireless Memory PDF资料下载
参数资料
| 型号： | PH28F640L18T85 |
| 厂商： | INTEL CORP |
| 元件分类： | PROM |
| 英文描述： | StrataFlash Wireless Memory |
| 中文描述： | 4M X 16 FLASH 1.8V PROM, 85 ns, PBGA56 |
| 封装： | 0.75 MM PITCH, LEAD FREE, VFBGA-56 |
| 文件页数： | 61/106页 |
| 文件大小： | 1272K |
| 代理商： | PH28F640L18T85 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页当前第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页
Intel StrataFlash Wireless Memory (L18)
Datasheet
Intel StrataFlash Wireless Memory (L18)
Order Number: 251902, Revision: 009
April 2005
61
WA0 must align with the start of an array buffer boundary
1
.
Buffered EFP considerations:
For optimum performance, cycling must be limited below 100 erase cycles per block
2
.
Buffered EFP programs one block at a time; all buffer data must fall within a single block
3
.
Buffered EFP cannot be suspended.
Programming to the flash memory array can occur only when the buffer is full
4
.
Read operation while performing Buffered EFP is not supported.
NOTES:
1.
Word buffer boundaries in the array are determined by A[4:0] (0x00 through 0x1F). The alignment start
point is A[4:0] = 0x00.
2.
Some degradation in performance may occur if this limit is exceeded, but the internal algorithm
continues to work properly.
3.
If the internal address counter increments beyond the block's maximum address, addressing wraps
around to the beginning of the block.
4.
If the number of words is less than 32, remaining locations must be filled with 0xFFFF.
11.3.2
Buffered EFP Setup Phase
After receiving the Buffered EFP Setup and Confirm command sequence, Status Register bit SR[7]
(Ready) is cleared, indicating that the WSM is busy with Buffered EFP algorithm startup. A delay
before checking SR[7] is required to allow the WSM enough time to perform all of its setups and
checks (Block-Lock status, V
PP
level, etc.). If an error is detected, SR[4] is set and Buffered EFP
operation terminates. If the block was found to be locked, SR[1] is also set. SR[3] is set if the error
occurred due to an incorrect V
PP
level.
Note:
Reading from the device after the Buffered EFP Setup and Confirm command sequence outputs
Status Register data. Do not issue the Read Status Register command; it will be interpreted as data
to be loaded into the buffer.
11.3.3
Buffered EFP Program/Verify Phase
After the Buffered EFP Setup Phase has completed, the host programming system must check
SR[7,0] to determine the availability of the write buffer for data streaming. SR[7] cleared indicates
the device is busy and the Buffered EFP program/verify phase is activated. SR[0] indicates the
write buffer is available.
Two basic sequences repeat in this phase: loading of the write buffer, followed by buffer data
programming to the array. For Buffered EFP, the count value for buffer loading is always the
maximum buffer size of 32 words. During the buffer-loading sequence, data is stored to sequential
buffer locations starting at address 0x00. Programming of the buffer contents to the flash memory
array starts as soon as the buffer is full. If the number of words is less than 32, the remaining buffer
locations must be filled with 0xFFFF.
Caution:
The buffer must be completely filled for programming to occur. Supplying an address outside of the
current block's range during a buffer-fill sequence causes the algorithm to exit immediately. Any
data previously loaded into the buffer during the fill cycle is not programmed into the array.
The starting address for data entry must be buffer size aligned, if not the Buffered EFP algorithm
will be aborted and the program fail (SR[4]) flag will be set.
相关PDF资料 |
PDF描述 |
|---|---|
| PH2907A | PNP switching transistor |
| PH2907 | PNP switching transistor |
| PH2931-135S | Rail-to-Rail, Very Low Noise Universal Dual Filter Building Block; Package: SO; No of Pins: 16; Temperature Range: -40°C to +85°C |
| PH2931-I3 | Radar Pulsed Power Transistor, 135W, 20ms Pulse, 1% Duty 2.9 - 3.1 GHz |
| PH2931-20M | Radar Pulsed Power Transistor, 20W,100ms Pulse, 10% Duty 2.9-3.1 GHz |
相关代理商/技术参数 |
参数描述 |
|---|---|
| PH28F640W18BD60 | 制造商:Micron Technology Inc 功能描述:PH28F640W18BD60S L785 |
| PH28F640W18BD60B | 制造商:Micron Technology Inc 功能描述:NUMPH28F640W18BD60B PH28F640W18BD60S L78 |
| PH28F640W18TE60B | 制造商:Micron Technology Inc 功能描述:64MB, CRYSTAL .75 VFBGA 1.8 LF - Tape and Reel |
| PH28F640W30BD70A | 制造商:Micron Technology Inc 功能描述:NOR Flash Parallel/Serial 1.8V 64Mbit 4M x 16bit 70ns 56-Pin VFBGA Tray 制造商:Micron Technology Inc 功能描述:NUMPH28F640W30BD70A MM#862859FLASH 28F64 |
| PH2-8-SGA | 制造商:Adam Technologies Inc 功能描述:PH2 Series Dual Row 8 Position Straight 2.54 mm Centerline Pin Header |
发布紧急采购，3分钟左右您将得到回复。