收藏本站
参数资料
型号： PIC18F45J50-I/ML
厂商： Microchip Technology
文件页数： 108/164页
文件大小： 0K
描述： IC PIC MCU FLASH 32K 2V 44-QFN
产品培训模块： XLP Deep Sleep Mode
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
标准包装： 45
系列： PIC® XLP™ 18F
核心处理器： PIC
芯体尺寸： 8-位
速度： 48MHz
连通性： I²C，SPI，UART/USART，USB
外围设备： 欠压检测/复位，DMA，POR，PWM，WDT
输入/输出数： 34
程序存储器容量： 32KB（16K x 16）
程序存储器类型： 闪存
RAM 容量： 3.8K x 8
电压 - 电源 (Vcc/Vdd)： 2.15 V ~ 3.6 V
数据转换器： A/D 13x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 44-VQFN 裸露焊盘
包装： 管件
产品目录页面： 657 (CN2011-ZH PDF)
配用： AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
PIC18F46J50 FAMILY
DS39931D-page 48
2011 Microchip Technology Inc.
TABLE 4-1:
LOW-POWER MODES
4.1.3
CLOCK TRANSITIONS AND STATUS
INDICATORS
The length of the transition between clock sources is
the sum of two cycles of the old clock source and three
to four cycles of the new clock source. This formula
assumes that the new clock source is stable.
Two bits indicate the current clock source and its
status:
OSTS
(OSCCON<3>)
and
T1RUN
(T1CON<6>). In general, only one of these bits will be
set in a given power-managed mode. When the OSTS
bit is set, the primary clock would be providing the
device clock. When the T1RUN bit is set, the Timer1
oscillator would be providing the clock. If neither of
these bits is set, INTRC would be clocking the device.
4.1.4
MULTIPLE SLEEP COMMANDS
The power-managed mode that is invoked with the
SLEEP
instruction is determined by the setting of the
IDLEN and DSEN bits at the time the instruction is exe-
cuted. If another SLEEP instruction is executed, the
device will enter the power-managed mode specified
by IDLEN and DSEN at that time. If IDLEN or DSEN
have changed, the device will enter the new
power-managed mode specified by the new setting.
4.2
Run Modes
In the Run modes, clocks to both the core and
peripherals are active. The difference between these
modes is the clock source.
4.2.1
PRI_RUN MODE
The PRI_RUN mode is the normal, full-power execu-
tion mode of the microcontroller. This is also the default
mode upon a device Reset unless Two-Speed Start-up
is enabled (see Section 27.4 “Two-Speed Start-up”
for details). In this mode, the OSTS bit is set (see
Section 3.5.1 “Oscillator Control Register”
).
4.2.2
SEC_RUN MODE
The SEC_RUN mode is the compatible mode to the
“clock switching” feature offered in other PIC18
devices. In this mode, the CPU and peripherals are
clocked from the Timer1 oscillator. This gives users the
option of low-power consumption while still using a
high-accuracy clock source.
SEC_RUN mode is entered by setting the SCS<1:0>
bits to ‘01’. The device clock source is switched to the
Timer1 oscillator (see Figure 4-1), the primary
oscillator is shut down, the T1RUN bit (T1CON<6>) is
set and the OSTS bit is cleared.
Mode
DSCONH<7>
OSCCON<7,1:0>
Module Clocking
Available Clock and Oscillator Source
DSEN(1)
IDLEN(1)
SCS<1:0>
CPU
Peripherals
Sleep
00
N/A
Off
Timer1 oscillator and/or RTCC may optionally be
enabled
Deep Sleep
10
N/A
Off(2)
Off
RTCC can run uninterrupted using the Timer1 or
internal low-power RC oscillator
PRI_RUN
0
N/A
00
Clocked
The normal, full-power execution mode; primary
clock source (defined by FOSC<2:0>)
SEC_RUN
0
N/A
01
Clocked
Secondary – Timer1 oscillator
RC_RUN
0
N/A
11
Clocked
Postscaled internal clock
PRI_IDLE
01
00
Off
Clocked
Primary clock source (defined by FOSC<2:0>)
SEC_IDLE
01
Off
Clocked
Secondary – Timer1 oscillator
RC_IDLE
01
11
Off
Clocked
Postscaled internal clock
Note 1:
IDLEN and DSEN reflect their values when the SLEEP instruction is executed.
2:
Deep Sleep turns off the voltage regulator for ultra low-power consumption. See Section 4.6 “Deep Sleep
Mode”
for more information.
Note:
Executing a SLEEP instruction does not
necessarily place the device into Sleep
mode. It acts as the trigger to place the
controller into either the Sleep or Deep
Sleep mode, or one of the Idle modes,
depending on the setting of the IDLEN bit.
Note:
The Timer1 oscillator should already be
running prior to entering SEC_RUN
mode. If the T1OSCEN bit is not set when
the SCS<1:0> bits are set to ‘01’, entry to
SEC_RUN mode will not occur. If the
Timer1 oscillator is enabled, but not yet
running, device clocks will be delayed until
the oscillator has started. In such situa-
tions, initial oscillator operation is far from
stable and unpredictable operation may
result.
相关PDF资料
PDF描述
ATMEGA128L-8AC IC AVR MCU 128K 8MHZ LV 64-TQFP
ATMEGA128-16AI IC AVR MCU 128K 16MHZ 64-TQFP
PIC24EP64GP202-I/SS MCU 16BIT 64KB FLASH 28SSOP
ATMEGA128-16AC IC AVR MCU 128K 16MHZ 64-TQFP
PIC18LF26J50-I/ML IC PIC MCU FLASH 64K 2V 28-QFN
相关代理商/技术参数
参数描述
PIC18F45J50T-I/ML 功能描述:8位微控制器 -MCU Full Spd USB 32KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45J50T-I/PT 功能描述:8位微控制器 -MCU Full Spd USB 32KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/ML 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 25 I/O 8B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/MV 功能描述:8位微控制器 -MCU 32KB FL 1536b RAM 8b Familynanowatt XLP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/P 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 25 I/O 8B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*