收藏本站
参数资料
型号： PIC18F45J50-I/ML
厂商： Microchip Technology
文件页数： 115/164页
文件大小： 0K
描述： IC PIC MCU FLASH 32K 2V 44-QFN
产品培训模块： XLP Deep Sleep Mode
PIC18 J Series MCU Overview
8-bit PIC® Microcontroller Portfolio
标准包装： 45
系列： PIC® XLP™ 18F
核心处理器： PIC
芯体尺寸： 8-位
速度： 48MHz
连通性： I²C，SPI，UART/USART，USB
外围设备： 欠压检测/复位，DMA，POR，PWM，WDT
输入/输出数： 34
程序存储器容量： 32KB（16K x 16）
程序存储器类型： 闪存
RAM 容量： 3.8K x 8
电压 - 电源 (Vcc/Vdd)： 2.15 V ~ 3.6 V
数据转换器： A/D 13x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 44-VQFN 裸露焊盘
包装： 管件
产品目录页面： 657 (CN2011-ZH PDF)
配用： AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
PIC18F46J50 FAMILY
DS39931D-page 54
2011 Microchip Technology Inc.
4.5.4
EXIT WITHOUT AN OSCILLATOR
START-UP DELAY
Certain exits from power-managed modes do not
invoke the OST at all. There are two cases:
PRI_IDLE mode (where the primary clock source
is not stopped) and the primary clock source is
the EC mode
PRI_IDLE mode and the primary clock source is
the ECPLL mode
In these instances, the primary clock source either
does not require an oscillator start-up delay, since it is
already running (PRI_IDLE), or normally does not
require an oscillator start-up delay (EC).
4.6
Deep Sleep Mode
Deep Sleep mode brings the device into its lowest
power consumption state without requiring the use of
external switches to remove power from the device.
During Deep Sleep, the on-chip VDDCORE voltage reg-
ulator is powered down, effectively disconnecting
power to the core logic of the microcontroller.
On devices that support it, the Deep Sleep mode is
entered by:
Setting the REGSLP (WDTCON<7>) bit
Clearing the IDLEN bit
Clearing the GIE bit
Setting the DSEN bit (DSCONH<7>)
Executing the SLEEP instruction immediately after
setting DSEN (no delay or interrupts in between)
In order to minimize the possibility of inadvertently enter-
ing Deep Sleep, the DSEN bit is cleared in hardware,
two instruction cycles after having been set. Therefore,
in order to enter Deep Sleep, the SLEEP instruction must
be executed in the immediate instruction cycle after set-
ting DSEN. If DSEN is not set when Sleep is executed,
the device will enter conventional Sleep mode instead.
During Deep Sleep, the core logic circuitry of the
microcontroller is powered down to reduce leakage
current. Therefore, most peripherals and functions of
the microcontroller become unavailable during Deep
Sleep. However, a few specific peripherals and func-
tions are powered directly from the VDD supply rail of
the microcontroller, and therefore, can continue to
function in Deep Sleep.
Entering Deep Sleep mode clears the DSWAKEL
register. However, if the Real-Time Clock and Calendar
(RTCC) is enabled prior to entering Deep Sleep, it will
continue to operate uninterrupted.
The device has a dedicated Brown-out Reset (DSBOR)
and Watchdog Timer Reset (DSWDT) for monitoring
voltage and time-out events in Deep Sleep. The
DSBOR and DSWDT are independent of the standard
BOR and WDT used with other power-managed modes
(Run, Idle and Sleep).
When a wake event occurs in Deep Sleep mode (by
MCLR Reset, RTCC alarm, INT0 interrupt, ULPWU or
DSWDT), the device will exit Deep Sleep mode and
perform a Power-on Reset (POR). When the device is
released from Reset, code execution will resume at the
device’s Reset vector.
4.6.1
PREPARING FOR DEEP SLEEP
Because VDDCORE could fall below the SRAM retention
voltage while in Deep Sleep mode, SRAM data could
be lost in Deep Sleep. Exiting Deep Sleep mode
causes a POR; as a result, most Special Function
Registers (SFRs) will reset to their default POR values.
Applications needing to save a small amount of data
throughout a Deep Sleep cycle can save the data to the
general purpose DSGPR0 and DSGPR1 registers. The
contents of these registers are preserved while the
device is in Deep Sleep, and will remain valid throughout
an entire Deep Sleep entry and wake-up sequence.
Note:
Since Deep Sleep mode powers down the
microcontroller by turning off the on-chip
VDDCORE voltage regulator, Deep Sleep
capability is available only on PIC18FXXJ
members in the device family. The on-chip
voltage regulator is not available on
PIC18LFXXJ members of the device
family, and therefore, they do not support
Deep Sleep.
相关PDF资料
PDF描述
ATMEGA128L-8AC IC AVR MCU 128K 8MHZ LV 64-TQFP
ATMEGA128-16AI IC AVR MCU 128K 16MHZ 64-TQFP
PIC24EP64GP202-I/SS MCU 16BIT 64KB FLASH 28SSOP
ATMEGA128-16AC IC AVR MCU 128K 16MHZ 64-TQFP
PIC18LF26J50-I/ML IC PIC MCU FLASH 64K 2V 28-QFN
相关代理商/技术参数
参数描述
PIC18F45J50T-I/ML 功能描述:8位微控制器 -MCU Full Spd USB 32KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45J50T-I/PT 功能描述:8位微控制器 -MCU Full Spd USB 32KB 4KBRAM nanoWatt RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/ML 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 25 I/O 8B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/MV 功能描述:8位微控制器 -MCU 32KB FL 1536b RAM 8b Familynanowatt XLP RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC18F45K20-E/P 功能描述:8位微控制器 -MCU 32KB Flash 1536B RAM 25 I/O 8B RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*