- 您现在的位置：买卖IC网 > PDF目录231009 > S29JL032H60TAI023 (ADVANCED MICRO DEVICES INC) 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 PDF资料下载
参数资料
| 型号： | S29JL032H60TAI023 |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 |
| 封装： | MO-142DD, TSOP-48 |
| 文件页数： | 28/66页 |
| 文件大小： | 1691K |
| 代理商： | S29JL032H60TAI023 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
32
S29JL032H
S29JL032H_00A11 March 10, 2005
Advan ce
In form ati o n
If DQ5 goes high during a program or erase operation, writing the reset command
returns the banks to the read mode (or erase-suspend-read mode if that bank
was in Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and device codes, and determine whether or not a sector is protected.
The autoselect command sequence may be written to an address within a bank
that is either in the read or erase-suspend-read mode. The autoselect command
may not be written while the device is actively programming or erasing in another
bank.
The autoselect command sequence is initiated by first writing two unlock cycles.
This is followed by a third write cycle that contains the bank address and the au-
toselect command. The bank then enters the autoselect mode. The system may
read any number of autoselect codes without reinitiating the command sequence.
Table 13 shows the address and data requirements. To determine sector protec-
tion information, the system must write to the appropriate bank address (BA) and
associated with each sector.
The system must write the reset command to return to the read mode (or erase-
suspend-read mode if the bank was previously in Erase Suspend).
Enter SecSi Sector/Exit SecSi Sector
Command Sequence
The SecSi Sector region provides a secured data area containing a random, six-
teen-byte electronic serial number (ESN). The system can access the SecSi
Sector region by issuing the three-cycle Enter SecSi Sector command sequence.
The device continues to access the SecSi Sector region until the system issues
the four-cycle Exit SecSi Sector command sequence. The Exit SecSi Sector com-
mand sequence returns the device to normal operation. The SecSi Sector is not
accessible when the device is executing an Embedded Program or embedded
Erase algorithm. Table 13 shows the address and data requirements for both com-
m a n d se qu en ce s. Se e also “SecSi ( S ecu red Sil ico n) Sec tor
Flash Memory Region” for further information. Note that the ACC function and un-
lock bypass modes are not available when the SecSi Sector is enabled.
Byte/Word Program Command Sequence
The system may program the device by word or byte, depending on the state of
the BYTE# pin. Programming is a four-bus-cycle operation. The program com-
mand sequence is initiated by writing two unlock write cycles, followed by the
program set-up command. The program address and data are written next, which
in turn initiate the Embedded Program algorithm. The system is not required to
provide further controls or timings. The device automatically provides internally
generated program pulses and verifies the programmed cell margin. Table 13
shows the address and data requirements for the byte program command
sequence.
When the Embedded Program algorithm is complete, that bank then returns to
the read mode and addresses are no longer latched. The system can determine
the status of the program operation by using DQ7, DQ6, or RY/BY#. Refer to the
Write Operation Status section for information on these status bits.
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL016D70BAI022 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| S29AL016D70TAN013 | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29AL016D90BFN013 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| SRL91-17UGR2-BB99 | ROCKER SWITCH, SPDT, MOMENTARY, PANEL MOUNT |
| SRL91-13AAR2-BB99 | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29JL032H60TAI210 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI211 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI212 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI213 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI220 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。