- 您现在的位置：买卖IC网 > PDF目录231009 > S29JL032H60TAI023 (ADVANCED MICRO DEVICES INC) 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 PDF资料下载
参数资料
| 型号： | S29JL032H60TAI023 |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 |
| 封装： | MO-142DD, TSOP-48 |
| 文件页数： | 40/66页 |
| 文件大小： | 1691K |
| 代理商： | S29JL032H60TAI023 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
March 10, 2005 S29JL032H_00A11
S29JL032H
43
Ad vance
Info rmat i o n
DQ2 toggles when the system reads at addresses within those sectors that have
been selected for erasure. (The system may use either OE# or CE# to control the
read cycles.) But DQ2 cannot distinguish whether the sector is actively erasing or
is erase-suspended. DQ6, by comparison, indicates whether the device is actively
erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected
for erasure. Thus, both status bits are required for sector and mode information.
Refer to Table 14 to compare outputs for DQ2 and DQ6.
Toggle Bit II” explains the algorithm. See also the DQ6: Toggle Bit I subsection.
between DQ2 and DQ6 in graphical form.
Reading Toggle Bits DQ6/DQ2
Refer to Figure 6 for the following discussion. Whenever the system initially be-
gins reading toggle bit status, it must read DQ15–DQ0 (or DQ7–DQ0 for x8-only
device) at least twice in a row to determine whether a toggle bit is toggling. Typ-
ically, the system would note and store the value of the toggle bit after the first
read. After the second read, the system would compare the new value of the tog-
gle bit with the first. If the toggle bit is not toggling, the device has completed
the program or erase operation. The system can read array data on DQ15–DQ0
(or DQ7–DQ0 for x8-only device) on the following read cycle.
However, if after the initial two read cycles, the system determines that the toggle
bit is still toggling, the system also should note whether the value of DQ5 is high
(see the section on DQ5). If it is, the system should then determine again
whether the toggle bit is toggling, since the toggle bit may have stopped toggling
just as DQ5 went high. If the toggle bit is no longer toggling, the device has suc-
cessfully completed the program or erase operation. If it is still toggling, the
device did not completed the operation successfully, and the system must write
the reset command to return to reading array data.
The remaining scenario is that the system initially determines that the toggle bit
is toggling and DQ5 has not gone high. The system may continue to monitor the
toggle bit and DQ5 through successive read cycles, determining the status as de-
scribed in the previous paragraph. Alternatively, it may choose to perform other
system tasks. In this case, the system must start at the beginning of the algo-
rithm when it returns to determine the status of the operation (top of Figure 6).
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified in-
ternal pulse count limit. Under these conditions DQ5 produces a “1,” indicating
that the program or erase cycle was not successfully completed.
The device may output a “1” on DQ5 if the system tries to program a “1” to a
location that was previously programmed to “0.” Only an erase operation can
change a “0” back to a “1.” Under this condition, the device halts the opera-
tion, and when the timing limit has been exceeded, DQ5 produces a “1.”
Under both these conditions, the system must write the reset command to return
to the read mode (or to the erase-suspend-read mode if a bank was previously
in the erase-suspend-program mode).
DQ3: Sector Erase Timer
After writing a sector erase command sequence, the system may read DQ3 to de-
termine whether or not erasure has begun. (The sector erase timer does not
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL016D70BAI022 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| S29AL016D70TAN013 | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29AL016D90BFN013 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| SRL91-17UGR2-BB99 | ROCKER SWITCH, SPDT, MOMENTARY, PANEL MOUNT |
| SRL91-13AAR2-BB99 | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29JL032H60TAI210 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI211 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI212 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI213 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI220 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。