- 您现在的位置：买卖IC网 > PDF目录231009 > S29JL032H60TAI023 (ADVANCED MICRO DEVICES INC) 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 PDF资料下载
参数资料
| 型号： | S29JL032H60TAI023 |
| 厂商： | ADVANCED MICRO DEVICES INC |
| 元件分类： | PROM |
| 英文描述： | 2M X 16 FLASH 3V PROM, 60 ns, PDSO48 |
| 封装： | MO-142DD, TSOP-48 |
| 文件页数： | 41/66页 |
| 文件大小： | 1691K |
| 代理商： | S29JL032H60TAI023 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页
44
S29JL032H
S29JL032H_00A11 March 10, 2005
Advan ce
In form ati o n
apply to the chip erase command.) If additional sectors are selected for erasure,
the entire time-out also applies after each additional sector erase command.
When the time-out period is complete, DQ3 switches from a “0” to a “1.” If the
time between additional sector erase commands from the system can be as-
sumed to be less than 50 s, the system need not monitor DQ3. See also the
Sector Erase Command Sequence section.
After the sector erase command is written, the system should read the status of
DQ7 (Data# Polling) or DQ6 (Toggle Bit I) to ensure that the device has accepted
the command sequence, and then read DQ3. If DQ3 is “1,” the Embedded Erase
algorithm has begun; all further commands (except Erase Suspend) are ignored
until the erase operation is complete. If DQ3 is “0,” the device will accept addi-
tional sector erase commands. To ensure the command has been accepted, the
system software should check the status of DQ3 prior to and following each sub-
sequent sector erase command. If DQ3 is high on the second status check, the
last command might not have been accepted.
Table 14 shows the status of DQ3 relative to the other status bits.
Table 14. Write Operation Status
Notes:
1. DQ5 switches to ‘1’ when an Embedded Program or Embedded Erase operation has exceeded the maximum timing
limits. Refer to the section on DQ5 for more information.
2. DQ7 and DQ2 require a valid address when reading status information. Refer to the appropriate subsection for further
details.
3. When reading write operation status bits, the system must always provide the bank address where the Embedded
Algorithm is in progress. The device outputs array data if the system addresses a non-busy bank.
Status
DQ7
DQ6
DQ5
DQ3
DQ2
RY/BY#
Standard
Mode
Embedded Program Algorithm
DQ7#
Toggle
0
N/A
No toggle
0
Embedded Erase Algorithm
0
Toggle
0
1
Toggle
0
Erase
Suspend
Mode
Erase-Suspend-
Read
Erase
Suspended Sector
1
No toggle
0
N/A
Toggle
1
Non-Erase
Suspended Sector
Data
1
Erase-Suspend-Program
DQ7#
Toggle
0
N/A
0
相关PDF资料 |
PDF描述 |
|---|---|
| S29AL016D70BAI022 | 1M X 16 FLASH 3V PROM, 70 ns, PBGA48 |
| S29AL016D70TAN013 | 1M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| S29AL016D90BFN013 | 1M X 16 FLASH 3V PROM, 90 ns, PBGA48 |
| SRL91-17UGR2-BB99 | ROCKER SWITCH, SPDT, MOMENTARY, PANEL MOUNT |
| SRL91-13AAR2-BB99 | ROCKER SWITCH, SPDT, LATCHED, PANEL MOUNT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S29JL032H60TAI210 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI211 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI212 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI213 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
| S29JL032H60TAI220 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:32M BIT CMOS 3.0V FLASH MEMORY |
发布紧急采购，3分钟左右您将得到回复。