- 您现在的位置：买卖IC网 > PDF目录98145 > ST72F651AR6T1 (STMICROELECTRONICS) 8-BIT, FLASH, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | ST72F651AR6T1 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, MICROCONTROLLER, PQFP64 |
| 封装： | 10 X 10 MM, ROHS COMPLIANT, TQFP-64 |
| 文件页数： | 102/161页 |
| 文件大小： | 2656K |
| 代理商： | ST72F651AR6T1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页当前第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页
ST72651AR6
45/161
Doc ID 7215 Rev 4
9 I/O PORTS
9.1 INTRODUCTION
Important note:
Please note that the I/O port configurations of this
device differ from those of the other ST7 devices.
The I/O ports offer different functional modes:
– transfer of data through digital inputs and outputs
and for specific pins:
– external interrupt generation
– alternate signal input/output for the on-chip pe-
ripherals.
An I/O port contains up to 8 pins. Each pin can be
programmed independently as digital input (with or
without interrupt generation) or digital output.
9.2 FUNCTIONAL DESCRIPTION
Each port has 2 main registers:
– Data Register (DR)
– Data Direction Register (DDR)
and one optional register:
– Option Register (OR)
Each I/O pin may be programmed using the corre-
sponding register bits in the DDR and OR regis-
ters: bit X corresponding to pin X of the port. The
same correspondence is used for the DR register.
The following description takes into account the
OR register, (for specific ports which do not pro-
vide this register refer to the I/O Port Implementa-
tion section). The generic I/O block diagram is
shown in Figure 31
9.2.1 Input Modes
The input configuration is selected by clearing the
corresponding DDR register bit.
In this case, reading the DR register returns the
digital value applied to the external I/O pin.
Different input modes can be selected by software
through the OR register.
Notes:
1. Writing the DR register modifies the latch value
but does not affect the pin status.
2. When switching from input to output mode, the
DR register has to be written first to drive the cor-
rect level on the pin as soon as the port is config-
ured as an output.
External interrupt function
When an I/O is configured as Input with Interrupt,
an event on this I/O can generate an external inter-
rupt request to the CPU.
Each pin can independently generate an interrupt
request. The interrupt sensitivity is independently
programmable using the sensitivity bits in the Mis-
cellaneous register.
Each external interrupt vector is linked to a dedi-
cated group of I/O port pins (see pinout description
and interrupt section). If several input pins are se-
lected simultaneously as interrupt source, these
are logically NANDed and inverted. For this rea-
son if one of the interrupt pins is tied low, it masks
the other ones.
In case of a floating input with interrupt configura-
tion, special care must be taken when changing
the configuration (see Figure 32).
When enabling/disabling an external interrupt by
changing port configuration (OR, DDR, control by
DTC), a spurious interrupt is generated if the pin
level is low and its edge sensitivity includes falling/
rising edge. This is due to the edge detector input
which is switched to '1' when the external interrupt
is disabled by port configuration.
To avoid this unwanted interrupt, a "safe" edge
sensitivity (rising edge for enabling and falling
edge for disabling) has to be selected before
changing the port configuration and configuring
the appropriate sensitivity again.
The external interrupts are hardware interrupts,
which means that the request latch (not accessible
directly by the application) is automatically cleared
when
the
corresponding
interrupt
vector
is
fetched.
1
相关PDF资料 |
PDF描述 |
|---|---|
| ST72P60E2M1 | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 |
| ST7260E2M1/XXX | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 |
| ST72T141K2M6XXX | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
| ST72T141K2M3XXX | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
| ST72T141K2MARE | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDSO34 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST72F651AR6T1E | 功能描述:8位微控制器 -MCU Flash 32K USB/DTC/I2 RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| ST72P262M6/OZXTR | 制造商:STMicroelectronics 功能描述:ST72P262M6/OZXTR |
| ST72P324TA/OBZTR | 制造商:STMicroelectronics 功能描述: |
| ST72P324TA/OHXTR | 制造商:STMicroelectronics 功能描述: |
| ST72P4T128M-A05AU | 制造商:STEC Inc 功能描述:1GB,ECC,REG,DDR2-400,UNLEAD - Bulk |
发布紧急采购，3分钟左右您将得到回复。