参数资料
型号: ST7FSCR1E4U1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC64
封装: QFN-64
文件页数: 13/101页
文件大小: 4506K
代理商: ST7FSCR1E4U1
ST7SCR1E4 ST7SCR1R4
19/101
CENTRAL PROCESSING UNIT (Cont’d)
Condition Code Register (CC)
Read/Write
Reset Value: 111x1xxx
The 8-bit Condition Code register contains the in-
terrupt masks and four flags representative of the
result of the instruction just executed. This register
can also be handled by the PUSH and POP in-
structions.
These bits can be individually tested and/or con-
trolled by specific instructions.
Arithmetic Management Bits
Bit 4 = H Half carry.
This bit is set by hardware when a carry occurs be-
tween bits 3 and 4 of the ALU during an ADD or
ADC instructions. It is reset by hardware during
the same instructions.
0: No half carry has occurred.
1: A half carry has occurred.
This bit is tested using the JRH or JRNH instruc-
tion. The H bit is useful in BCD arithmetic subrou-
tines.
Bit 2 = N Negative.
This bit is set and cleared by hardware. It is repre-
sentative of the result sign of the last arithmetic,
logical or data manipulation. It’s a copy of the re-
sult 7th bit.
0: The result of the last operation is positive or null.
1: The result of the last operation is negative
(i.e. the most significant bit is a logic 1).
This bit is accessed by the JRMI and JRPL instruc-
tions.
Bit 1 = Z Zero.
This bit is set and cleared by hardware. This bit in-
dicates that the result of the last arithmetic, logical
or data manipulation is zero.
0: The result of the last operation is different from
zero.
1: The result of the last operation is zero.
This bit is accessed by the JREQ and JRNE test
instructions.
Bit 0 = C Carry/borrow.
This bit is set and cleared by hardware and soft-
ware. It indicates an overflow or an underflow has
occurred during the last arithmetic operation.
0: No overflow or underflow has occurred.
1: An overflow or underflow has occurred.
This bit is driven by the SCF and RCF instructions
and tested by the JRC and JRNC instructions. It is
also affected by the “bit test and branch”, shift and
rotate instructions.
Interrupt Management Bits
Bit 5,3 = I1, I0 Interrupt
The combination of the I1 and I0 bits gives the cur-
rent interrupt software priority.
These two bits are set/cleared by hardware when
entering in interrupt. The loaded value is given by
the corresponding bits in the interrupt software pri-
ority registers (IxSPR). They can be also set/
cleared by software with the RIM, SIM, IRET,
HALT, WFI and PUSH/POP instructions.
See the interrupt management chapter for more
details.
7
0
1
I1
H
I0
N
Z
C
Interrupt Software Priority
I1
I0
Level 0 (main)
1
0
Level 1
0
1
Level 2
0
Level 3 (= interrupt disable)
1
相关PDF资料
PDF描述
ST7SCR1T1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST7SCR1E4U1/XXX MICROCONTROLLER, QCC24
ST7SCR1E4M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
ST7L34F2MCRE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
ST7L35F2MARE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
相关代理商/技术参数
参数描述
ST7FSCR1R4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT LOW-POWER, FULL-SPEED USB MCU WITH 16K FLASH, 768 RAM, SMARTCARD I/F, TIMER
ST7FSCR1R4T1 功能描述:8位微控制器 -MCU 8-BIT Lw Pwr USB MCU W/ 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FUS-PRIMER 功能描述:程序设计器 - 基于处理器 Low-Cost Eval Dev Tool Pack RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V
ST7FUS-SK/RAIS 制造商:STMicroelectronics 功能描述:Evaluation and Application Development with ST7Ultralite
ST7GEME4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Full-speed USB MCU with smartcard firmware and EMV/non-EMV interface