参数资料
型号: ST7FSCR1E4U1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC64
封装: QFN-64
文件页数: 46/101页
文件大小: 4506K
代理商: ST7FSCR1E4U1
ST7SCR1E4 ST7SCR1R4
49/101
USB INTERFACE (Cont’d)
INTERRUPT MASK REGISTER (USBIMR)
Read/Write
Reset Value: 0000 0000 (00h)
These bits are mask bits for all the interrupt condi-
tion bits included in the USBISTR register. When-
ever one of the USBIMR bits is set, if the corre-
sponding USBISTR bit is set, and the I- bit in the
CC register is cleared, an interrupt request is gen-
erated. For an explanation of each bit, please refer
to the description of the USBISTR register.
CONTROL REGISTER (USBCTLR)
Read/Write
Reset value: 0000 0110 (06h)
Bit 7 = RSM Resume Detected
This bit shows when a resume sequence has start-
ed on the USB port, requesting the USB interface
to wake-up from suspend state. It can be used to
determine the cause of an ESUSP event.
0: No resume sequence detected on USB
1: Resume sequence detected on USB
Bit 6 = USB_RST USB Reset detected.
This bit shows that a reset sequence has started
on the USB. It can be used to determine the cause
of an ESUSP event (Reset sequence).
0: No reset sequence detected on USB
1: Reset sequence detected on USB
Bits [5:4] = Reserved, forced by hardware to 0.
Bit 3 = RESUME Resume.
This bit is set by software to wake-up the Host
when the ST7 is in suspend mode.
0: Resume signal not forced
1: Resume signal forced on the USB bus.
Software should clear this bit after the appropriate
delay.
Bit 2 = PDWN Power down.
This bit is set by software to turn off the 3.3V on-
chip voltage regulator that supplies the external
pull-up resistor and the transceiver.
0: Voltage regulator on
1: Voltage regulator off
Note: After turning on the voltage regulator, soft-
ware should allow at least 3 s for stabilisation of
the power supply before using the USB interface.
Bit 1 = FSUSP Force suspend mode.
This bit is set by software to enter Suspend mode.
The ST7 should also be put in Halt mode to reduce
power consumption.
0: Suspend mode inactive
1: Suspend mode active
When the hardware detects USB activity, it resets
this bit (it can also be reset by software).
Bit 0 = FRES Force reset.
This bit is set by software to force a reset of the
USB interface, just as if a RESET sequence came
from the USB.
0: Reset not forced
1: USB interface reset forced.
The USB is held in RESET state until software
clears this bit, at which point a “USB-RESET” in-
terrupt will be generated if enabled.
7
0
CTRM
0
SOVR
M
ERRM
SUSP
M
ESUSP
M
RESET
M
SOFM
7
0
RSM
USB_
RST
0
RESU
ME
PDWN
FSUSP
FRES
相关PDF资料
PDF描述
ST7SCR1T1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST7SCR1E4U1/XXX MICROCONTROLLER, QCC24
ST7SCR1E4M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
ST7L34F2MCRE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
ST7L35F2MARE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
相关代理商/技术参数
参数描述
ST7FSCR1R4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT LOW-POWER, FULL-SPEED USB MCU WITH 16K FLASH, 768 RAM, SMARTCARD I/F, TIMER
ST7FSCR1R4T1 功能描述:8位微控制器 -MCU 8-BIT Lw Pwr USB MCU W/ 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FUS-PRIMER 功能描述:程序设计器 - 基于处理器 Low-Cost Eval Dev Tool Pack RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V
ST7FUS-SK/RAIS 制造商:STMicroelectronics 功能描述:Evaluation and Application Development with ST7Ultralite
ST7GEME4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Full-speed USB MCU with smartcard firmware and EMV/non-EMV interface