参数资料
型号: ST7FSCR1E4U1
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, QCC64
封装: QFN-64
文件页数: 65/101页
文件大小: 4506K
代理商: ST7FSCR1E4U1
ST7SCR1E4 ST7SCR1R4
66/101
SMARTCARD INTERFACE (Cont’d)
SMARTCARD CONTACT CONTROL REGISTER
(CRDCCR)
Read/Write
Reset Value: 00xx xx00 (xxh)
Note: To modify the content of this register, the LD
instruction must be used (do not use the BSET
and BRES instructions).
Bit 7 = CLKSEL Card clock selection.
This bit is set and cleared by software.
0: The signal on the CRDCLK pin is a copy of the
CRDCLK bit.
1: The signal on the CRDCLK pin is a 4MHz fre-
quency clock.
Note: To start the clock at a known level, the CRD-
CLK bit should be changed before the CLKSEL
bit.
Bit 6 = Reserved, must be kept cleared.
Bit 5 = CRDC8 CRDC8 pin control.
Reading this bit returns the value present on the
CRDC8 pin. Writing this bit outputs the bit value on
the pin.
Bit 4 = CRDC4 CRDC4 pin control
Reading this bit returns the value present on the
CRDC4 pin. Writing this bit outputs the bit value on
the pin.
Bit 3 = CRDIO CRDIO pin control.
This bit is active only if the UART bit in the CRDCR
Register is reset. Reading this bit returns the value
present on the CRDIO pin.
If the UART bit is reset:
– Writing “0” forces a low level on the CRDIO pin
– Writing “1” forces the CRDIO pin to open drain
Hi-Z.
Bit 2 = CRDCLK CRDCLK pin control
This bit is active only if the CLKSEL bit of the CRD-
CCR register is reset. Reading this bit returns the
value present in the register (not the CRDCLK pin
value).
When the CLKSEL bit is reset:
0: Level 0 to be applied on CRDCLK pin.
1: Level 1 to be applied on CRDCLK pin.
Note: To ensure that the clock stops at a given
value, write the desired value in the CRDCLK bit
prior to changing the CLKSEL bit from 1 to 0.
Bit 1 = CRDRST CRDRST pin control.
Reading this bit returns the value present on the
CRDRST pin. Writing this bit outputs the bit value
on the pin.
Bit 0 = CRDVCC CRDVCC Pin Control.
This bit is set and cleared by software and forced
to 0 by hardware when no card is present
(CRDIRF bit=0).
0: No voltage to be applied on the CRDVCC pin.
1: The selected voltage must be applied on the
CRDVCC pin.
Figure 39. Smartcard I/O Pin Structure
7
0
CLK
SEL
-
CRD
C8
CRD
C4
CRD
IO
CRD
CLK
CRD
RST
CRD
VCC
I/O PIN
DATA BUS
CRDCCR
REGISTER
相关PDF资料
PDF描述
ST7SCR1T1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64
ST7SCR1E4U1/XXX MICROCONTROLLER, QCC24
ST7SCR1E4M1/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24
ST7L34F2MCRE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
ST7L35F2MARE/XXX 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20
相关代理商/技术参数
参数描述
ST7FSCR1R4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT LOW-POWER, FULL-SPEED USB MCU WITH 16K FLASH, 768 RAM, SMARTCARD I/F, TIMER
ST7FSCR1R4T1 功能描述:8位微控制器 -MCU 8-BIT Lw Pwr USB MCU W/ 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ST7FUS-PRIMER 功能描述:程序设计器 - 基于处理器 Low-Cost Eval Dev Tool Pack RoHS:否 制造商:Olimex Ltd. 产品:Programmers 工具用于评估:XMEGA, MegaAVR, tinyAVR 核心:AVR 接口类型:USB 工作电源电压:1.8 V to 5.5 V
ST7FUS-SK/RAIS 制造商:STMicroelectronics 功能描述:Evaluation and Application Development with ST7Ultralite
ST7GEME4 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Full-speed USB MCU with smartcard firmware and EMV/non-EMV interface