参数资料
型号: TMX320LF2403AVFS
厂商: Texas Instruments, Inc.
元件分类: 数字信号处理
英文描述: DSP CONTROLLERS
中文描述: DSP控制器
文件页数: 43/134页
文件大小: 1759K
代理商: TMX320LF2403AVFS
TMS320LF2407A,TMS320LF2406A,TMS320LF2403A,TMS320LF2402A
TMS320LC2406A,TMS320LC2404A,TMS320LC2403A,TMS320LC2402A
DSP CONTROLLERS
SPRS145K JULY 2000 REVISED AUGUST 2005
16
POST OFFICE BOX 1443
HOUSTON, TEXAS 772511443
pin functions (continued)
Table 2. LF240xA and LC240xA Pin List and Package Options (Continued)
PIN NAME
LF2407A
(144-PGE)
2406A
(100-PZ)
LC2404A
(100-PZ)
2403A,
LC2402A
(64-PAG)
and
2402A
(64-PG)
DESCRIPTION
EMULATION AND TEST (CONTINUED)
TDI
139
96
30
JTAG test data input (TDI) with internal pullup. TDI
is clocked into the selected register (instruction or
data) on a rising edge of TCK. (
↑)
TDO
142
99
31
JTAG scan out, test data output (TDO). The
contents of the selected register (instruction or
data) is shifted out of TDO on the falling edge of
TCK. (
↓)
TMS
144
100
32
JTAG test-mode select (TMS) with internal pullup.
This serial control input is clocked into the TAP
controller on the rising edge of TCK. (
↑)
TMS2
36
25
48
JTAG test-mode select 2 (TMS2) with internal
pullup. This serial control input is clocked into the
TAP controller on the rising edge of TCK. Used for
test and emulation only. This pin can be left
unconnected in user applications. If the PLL bypass
mode is desired, TMS2, TMS, and TRST should be
held low during reset. (
↑)
TRST
1
33
JTAG test reset with internal pulldown. TRST, when
driven high, gives the scan system control of the
operations of the device. If this signal is not
connected or driven low, the device operates in its
functional mode, and the test reset signals are
ignored. (
↓)
NOTE: Do not use pullup resistors on TRST; it has
an internal pulldown device. TRST is an active high
test pin and must be maintained low at all times
during normal device operation. In a low-noise
environment, TRST may be left floating. In other
instances, an external pulldown resistor is highly
recommended. The value of this resistor should be
based on drive strength of the debugger pods
applicable to the design. A 2.2-k
resistor generally
offers
adequate
protection.
Since
this
is
applicationspecific, it is recommended that each
target board be validated for proper operation of the
debugger and the application. (I
↓)
Bold, italicized pin names indicate pin function after reset.
GPIO General-purpose input/output pin. All GPIOs come up as input after reset.
§ It is highly recommended that VCCA be isolated from the digital supply voltage (and VSSA from digital ground) to maintain the specified accuracy
and improve the noise immunity of the ADC.
Only when all of the following conditions are met: EMU1/OFF is low, TRST is low, and EMU0 is high
# No power supply pin (VDD, VDDO, VSS, or VSSO) should be left unconnected. All power supply pins must be connected appropriately for proper
device operation.
LEGEND:
↑ Internal pullup
↓ Internal pulldown
(Typical active pullup/pulldown value is
±16 A.)
相关PDF资料
PDF描述
TMX320LF2404APAGA DSP CONTROLLERS
TMX320LF2404APAGS DSP CONTROLLERS
TMX320LF2404APGA DSP CONTROLLERS
TMX320LF2404APGEA DSP CONTROLLERS
TMX320LF2404APGES DSP CONTROLLERS
相关代理商/技术参数
参数描述
TMX320LF2404APAGA 制造商:TI 制造商全称:Texas Instruments 功能描述:DSP CONTROLLERS
TMX320LF2404APAGS 制造商:TI 制造商全称:Texas Instruments 功能描述:DSP CONTROLLERS
TMX320LF2404APGA 制造商:TI 制造商全称:Texas Instruments 功能描述:DSP CONTROLLERS
TMX320LF2404APGEA 制造商:TI 制造商全称:Texas Instruments 功能描述:DSP CONTROLLERS
TMX320LF2404APGES 制造商:TI 制造商全称:Texas Instruments 功能描述:DSP CONTROLLERS