- 您现在的位置：买卖IC网 > PDF目录68428 > W25X20BLSNIG (WINBOND ELECTRONICS CORP) 2M X 1 FLASH 2.7V PROM, PDSO8 PDF资料下载
参数资料
| 型号： | W25X20BLSNIG |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | PROM |
| 英文描述： | 2M X 1 FLASH 2.7V PROM, PDSO8 |
| 封装： | 0.150 INCH, GREEN, PLASTIC, SOIC-8 |
| 文件页数： | 53/53页 |
| 文件大小： | 2041K |
| 代理商： | W25X20BLSNIG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页当前第53页
W25X10BL/20BL/40BL
Publication Release Date: October 14, 2009
- 9 -
Preliminary -- Revision A
8.
FUNCTIONAL DESCRIPTION
8.1
SPI OPERATIONS
8.1.1
Standard SPI Instructions
The W25X10BL/20BL/40BL are accessed through an SPI compatible bus consisting of four signals:
Serial Clock (CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard
SPI instructions use the DI input pin to serially write instructions, addresses or data to the device on the
rising edge of CLK. The DO output pin is used to read data or status from the device on the falling
edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0
and Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and
data is not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the
falling and rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising
edges of /CS..
8.1.2
Dual SPI Instructions
The W25X10BL/20BL/40BL supports Dual SPI operation when using the “Fast Read Dual Output
(3Bh)” and “Fast Read Dual I/O (BBh)” instructions. These instructions allow data to be transferred to
or from the device at two to three times the rate of ordinary Serial Flash devices. The Dual SPI Read
instructions are ideal for quickly downloading code to RAM upon power-up (code-shadowing) or for
executing non-speed-critical code directly from the SPI bus (XIP). When using Dual SPI instructions,
the DI and DO pins become bidirectional I/O pins: IO0 and IO1.
8.1.3
Hold Function
The /HOLD signal allows the W25X10BL/20BL/40BL operation to be paused while it is actively
selected (when /CS is low). The /HOLD function may be useful in cases where the SPI data and clock
signals are shared with other devices. For example, consider if the page buffer was only partially
written when a priority interrupt requires use of the SPI bus. In this case the /HOLD function can save
the state of the instruction and the data in the buffer so programming can resume where it left off once
the bus is available again.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low
the /HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate
on the rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will terminate after the next falling edge of CLK.
During a /HOLD condition, the Serial Data Output (DO) is high impedance, and Serial Data
Input/Output (DIO) and Serial Clock (CLK) are ignored. The Chip Select (/CS) signal should be kept
active (low) for the full duration of the /HOLD operation to avoid resetting the internal logic state of the
device.
相关PDF资料 |
PDF描述 |
|---|---|
| W25X20BLZPIG | 2M X 1 FLASH 2.7V PROM, PDSO8 |
| W25X32AVDAIZ | 4M X 8 FLASH 2.7V PROM, PDIP8 |
| W25X40-VSNI | 4M X 1 FLASH 2.7V PROM, PDSO8 |
| W25X80-VSNI-G | 8M X 1 FLASH 2.7V PROM, PDSO8 |
| W25X40BVDAIG | 4M X 1 FLASH 2.7V PROM, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W25X20BLZPIG | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT AND 4M-BIT 2.5V SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI |
| W25X20BV | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M-BIT, 2M-BIT AND 4M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI |
| W25X20BVSNIG | 功能描述:IC SPI FLASH 2MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR) |
| W25X20BVZPIG | 功能描述:IC SPI FLASH 2MBIT 8WSON RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:1,000 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:4K (512 x 8) 速度:400kHz 接口:I²C，2 线串口 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商设备封装:8-MFP 包装:带卷 (TR) |
| W25X20CLSNIG | 功能描述:IC FLASH SPI 2MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,000 系列:- 格式 - 存储器:RAM 存储器类型:SRAM - 异步 存储容量:256K (32K x 8) 速度:15ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 封装/外壳:28-TSSOP（0.465"，11.8mm 宽） 供应商设备封装:28-TSOP 包装:带卷 (TR) 其它名称:71V256SA15PZGI8 |
发布紧急采购，3分钟左右您将得到回复。