参数资料
| 型号： | W947D6HBHX5E |
| 厂商： | Winbond Electronics |
| 文件页数： | 40/60页 |
| 文件大小： | 0K |
| 描述： | IC LPDDR SDRAM 128MBIT 60VFBGA |
| 标准包装： | 312 |
| 格式 - 存储器： | RAM |
| 存储器类型： | 移动 LPDDR SDRAM |
| 存储容量： | 128M（8Mx16） |
| 速度： | 200MHz |
| 接口： | 并联 |
| 电源电压： | 1.7 V ~ 1.95 V |
| 工作温度： | -25°C ~ 85°C |
| 封装/外壳： | 60-TFBGA |
| 供应商设备封装： | 60-VFBGA（8x9） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页
W947D6HB / W947D2HB
128Mb Mobile LPDDR
7.7.1 Precharge Command
CK
CK
CKE
(High)
CS
RAS
CAS
WE
Address
All Banks
A10
One Bank
BA0,BA1
BA
= Don't Care
BA=BANK Address
(if A10 = L,otherwise Don't Care)
7.8 Auto Precharge
Auto Precharge is a feature which performs the same individual bank precharge function as described above, but
without requiring an explicit command. This is accomplished by using A10 (A10 = High), to enable Auto Precharge in
conjunction with a specific READ or WRITE command. A precharge of the bank / row that is addressed with the
READ or WRITE command is automatically performed upon completion of the read or write burst. Auto Precharge is
non persistent in that it is either enabled or disabled for each individual READ or WRITE command.
Auto Precharge ensures that a precharge is initiated at the earliest valid stage within a burst. The user must not
issue another command to the same bank until the precharing time (t RP ) is completed. This is determined as if an
explicit PRECHARGE command was issued at the earliest possible time, as described for each burst type in the
Operation section of this specification.
7.9 Refresh Requirements
LPDDR SDRAM devices require a refresh of all rows in any rolling 64ms interval. Each refresh is generated in one of
two ways: by an explicit AUTO REFRESH command, or by an internally timed event in SELF REFRESH mode.
Dividing the number of device rows into the rolling 64ms interval defines the average refresh interval (t REFI ), which is
a guideline to controllers for distributed refresh timing.
7.10 Auto Refresh
AUTO REFRESH command is used during normal operation of the LPDDR SDRAM. This command is non
persistent, so it must be issued each time a refresh is required.
The refresh addressing is generated by the internal refresh controller. The LPDDR SDRAM requires AUTO
REFRESH commands at an average periodic interval of t REFI.
Publication Release Date:Jun,17, 2011
- 40 -
Revision A01-003
相关PDF资料 |
PDF描述 |
|---|---|
| W25Q64DWZPIG | IC FLASH SPI 64MBIT 8WSON |
| M1A3P400-FGG256I | IC FPGA 1KB FLASH 400K 256-FBGA |
| M1A3P400-FG256I | IC FPGA 1KB FLASH 400K 256-FBGA |
| EPF6024AQC208-2N | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF6024AQC208-2 | IC FLEX 6000 FPGA 24K 208-PQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W947D6HBHX5I | 制造商:WINBOND 制造商全称:Winbond 功能描述:128Mb Mobile LPDDR |
| W947D6HBHX5I TR | 制造商:Winbond Electronics Corp 功能描述: |
| W947D6HBHX6E | 制造商:Winbond Electronics Corp 功能描述:IC LPDDR SDRAM 128MBIT 60VFBGA |
| W947D6HBHX6G | 制造商:WINBOND 制造商全称:Winbond 功能描述:128Mb Mobile LPDDR |
| W948D2FB | 制造商:WINBOND 制造商全称:Winbond 功能描述:256Mb Mobile LPDDR |
发布紧急采购，3分钟左右您将得到回复。