- 您现在的位置：买卖IC网 > PDF目录11831 > XR16C2852IJTR-F (Exar Corporation)IC UART FIFO 128B 44PLCC PDF资料下载
参数资料
| 型号： | XR16C2852IJTR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 19/51页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 128B 44PLCC |
| 标准包装： | 500 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 128 字节 |
| 规程： | RS232，RS485 |
| 电源电压： | 2.97 V ~ 5.5 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC（16.59x16.59） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
XR16C2852
xr
2.97V TO 5.5V DUAL UART WITH 128-BYTE FIFOS
REV. 2.1.1
26
]
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[5:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels (See Table 9). See “Section
4.4.1, Interrupt Generation:” on page 25 and “Section 4.4.2, Interrupt Clearing:” on page 25 for details.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
4.5
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode. The DMA, and FIFO modes are defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No receive FIFO reset (default)
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
FCR[2]: TX FIFO Reset
This bit is only active when FCR bit-0 is a ‘1’.
Logic 0 = No transmit FIFO reset (default).
Logic 1 = Reset the transmit FIFO pointers and FIFO level counter logic (the transmit shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
TABLE 9: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Receive Data Time-out)
3
0
1
0
RXRDY (Received Data Ready)
4
0
1
0
TXRDY (Transmit Ready)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xoff or Special character)
7
1
0
CTS#, RTS# change of state
-
0
1
None (default)
相关PDF资料 |
PDF描述 |
|---|---|
| XR16C2850IJTR-F | IC UART FIFO 128B 44PLCC |
| XR16V554IV-F | IC UART FIFO 16B QUAD 64LQFP |
| VE-B5L-IW-F1 | CONVERTER MOD DC/DC 28V 100W |
| VE-B5L-IX-F4 | CONVERTER MOD DC/DC 28V 75W |
| VE-B5L-IX-F2 | CONVERTER MOD DC/DC 28V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR-16C450CJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-16C450CP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-16C452CJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-16C550CJ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
| XR-16C550CP | 制造商:未知厂家 制造商全称:未知厂家 功能描述:UART |
发布紧急采购，3分钟左右您将得到回复。